Simon Glass [Wed, 20 Oct 2021 03:43:23 +0000 (21:43 -0600)]
buildman: Write output even on fatal error
At present buildman does not write any output (to the 'out' and 'err)
files if the build terminates with a fatal error. This is to avoid adding
lots of spam to the logs.
However there are times when this is actually useful, such as when the
build fails for an obscure reason such as a Kconfig loop.
Update the logic to always write the output, so that the user gets a clue
as to what is happening.
Marek Vasut [Sat, 11 Sep 2021 22:40:00 +0000 (00:40 +0200)]
ARM: imx: mx5: Add altbootcmd and resets to M53Menlo
Bulletproof the default boot command with reset statements in case
any command in the chain would fail. In case a failure were to happen,
the board will reset, increment boot counter and retry the procedure.
In case the failures persist and the boot counter reaches the bootlimit,
U-Boot starts altbootcmd instead of the default bootcmd boot command.
The altbootcmd swaps the default boot partition for the other boot
partition, which is an identical copy or an older copy, and tries
booting from that one instead.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP
Import HS400 support for iMX7ULP B0 from the Linux kernel:
2eaf5a533afd ("mmc: sdhci-esdhc-imx: Add HS400 support for iMX7ULP")
According to IC suggest, need to clear the STROBE_DLL_CTRL_RESET
before any setting of STROBE_DLL_CTRL register.
USDHC has register bits(bit[27~20] of register STROBE_DLL_CTRL)
for slave sel value. If this register bits value is 0, it needs
256 ref_clk cycles to update slave sel value. IC suggest to set
bit[27~20] to 0x4, it only need 4 ref_clk cycle to update slave
sel value. This will short the lock time of slave.
i.MX7ULP B0 will need more time to lock the REF and SLV, so change
to add 5us delay.
Peng Fan [Mon, 16 Aug 2021 03:48:45 +0000 (11:48 +0800)]
imx: makefile: drop the use of imx8mimage.sh
After switch to use binman, no need to use the bash script
to check file exsiting or not. And there is bug that
the script will be executed everytime Makefile is used which is
confusing people.
Signed-off-by: Peng Fan <peng.fan@nxp.com> Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Peng Fan [Mon, 16 Aug 2021 03:48:41 +0000 (11:48 +0800)]
tools: imx8mimage: not abort when mmap fail
When creating flash.bin, the hdmi firmware might not be
copied to U-Boot source tree. Then mkimage will fail.
However we are switching to binman, binman will show the
message if the file not there, and create empty file per
i.MX8MQ binman node. So we not fail mkimage here othersize
CI will fail if hdmi firmware not copied here.
Tim Harvey [Wed, 29 Sep 2021 22:04:22 +0000 (15:04 -0700)]
imx: ventana: fix USB hub reset
Remove board_ehci_hcd_init function that is not used with DM_USB
and replace its functionality with device-tree configuraton that treats
USB HUB RST# as a gpio enable for the usbh1 vbus regulator.
Tim Harvey [Wed, 29 Sep 2021 22:04:21 +0000 (15:04 -0700)]
imx: ventana: update LVDS support
Enable LVDS display detection and panel-specific configuration
Make I2C based LVDS detection and configuration model specific:
- not all boards support LVDS connectors; fail detection that do not
support LVDS to avoid misdetecting an I2C device as a display
- GPIO configuration is panel specific; use panel name where needed
Tim Harvey [Wed, 29 Sep 2021 22:04:18 +0000 (15:04 -0700)]
imx: ventana: remove phy gpio reset from dt
We configure network phy configuration for internal delay, LED config,
and clock config. If we leave the phy reset gpio defined in dt the
kernel may issue a reset to the phy and break these configs. While some
may be handled by a kernel phy driver, others may not (typically LED
config).
imx: imx6ul: Add support for Kontron Electronics SL/BL i.MX6UL/ULL boards (N63xx/N64xx)
This adds support for i.MX6UL/ULL-based evaluation kits with SoMs by
Kontron Electronics GmbH.
Currently there are the following SoM flavors (SoM-Line):
* N6310: SOM with i.MX6UL-2, 256MB RAM, 256MB SPI NAND
* N6311: SOM with i.MX6UL-2, 512MB RAM, 512MB SPI NAND
* N6411: SOM with i.MX6ULL, 512MB RAM, 512MB SPI NAND
And the according evaluation boards (Board-Line):
* N6310-S: Baseboard with SOM N6310, eMMC, display (optional), ...
* N6311-S: Baseboard with SOM N6311, eMMC, display (optional), ...
* N6411-S: Baseboard with SOM N6411, eMMC, display (optional), ...
Currently U-Boot describes i.MX6UL and i.MX6ULL through separate config
options at compile-time. Though the differences are so minor, that for
the scope of these SoMs we just use a single defconfig that is compatible
with both SoCs.
The CONFIG_SPL_MAX_SIZE definition did not account for all areas that
are used by the boot ROM according to the manual, causing boot failures
due to truncated SPL images when actually hitting this limit.
Synchronize the u-boot and kernel imx device trees, using tuned
script from commit c0157bdcafa1 ("ARM: dts: imx: use generic name bus")
Per devicetree specification, generic names are recommended to be
used, such as bus.
i.MX AIPS is an AHB - IP bridge bus, so we could use bus as node
name.
Script:
sed -i "s/\<aips@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips@/bus@/" arch/arm/dts/vf*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/imx*.dtsi
sed -i "s/\<aips-bus@/bus@/" arch/arm/dts/vf*.dtsi
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io> Reviewed-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Thu, 23 Sep 2021 14:01:15 +0000 (17:01 +0300)]
mx7ulp: Update wdog disable sequence
Update the mx7ulp wdog disable sequence to avoid potential reset
issue in unlock or refresh sequence. Both sequence need two words
write to wdog CNT register in 16 bus clocks window, if miss the
window, the write will cause violation in wdog and reset the chip.
Current u-boot code is using writel() function which has a DMB
barrier to order the memory access. The DMB between two words write
may introduce some delay in certain circumstance, causing the wdog
reset due to 16 bus clock window requirement.
Also, WDOG1 might have been enabled already depending on FUSE hence
we need to be as close as possible to its reconfiguration timing
requirement of 128 bus clock limit.
This patch replaces writel() function by __raw_writel() to avoid such
issue, and improve to check if watchdog is already disabled or
unlocked.
Marek Vasut [Sat, 11 Sep 2021 22:43:18 +0000 (00:43 +0200)]
ARM: dts: imx8mm-verdin: Set PHY mode to RGMII-ID
Since c6df0e2ffdc ("net: phy: micrel: add support for DLL setup on ksz9131")
the Micrel PHY driver correctly configures the delay register. The Verdin PHY
is RGMII-ID, so reflect that in DT, otherwise the ethernet no longer works.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The BSP platform LmP supports the board NXP iMX8QM MEK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
The BSP platform LmP supports the board NXP iMX8M Plus EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
The BSP platform LmP supports the board NXP iMX8M Mini EVK. The
kernel size in LmP exceeds 32Mb. Increase the maximum size
of an uncompressed kernel to fix the following error:
Uncompressing Kernel Image
Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
arm: imx8m: imx8mm-cl-iot-gate: Add support for detect memory size
When purchasing imx8mm-cl-iot-gate it is able to customize the
memory size. It could be 1GB, 2GB and 4GB. We implement
board_phys_sdram_size() to detect the memory size for usage.
Andrey Zhizhikin [Tue, 24 Aug 2021 07:55:14 +0000 (09:55 +0200)]
tree: imx: remove old fit generator script
Since derivatives are moving to binman from usage of the FIT generator
script, and considering the warning introduced in f4a43d2925
("Makefile: Warn against using CONFIG_SPL_FIT_GENERATOR"), usage of FIT
generator is discouraged.
Current FIT generator also generates broken output, since commit 3f04db891a ("image: Check for unit addresses in FITs") prohibits using
'@' for unit addresses but the generator script still emits the old
sematics.
Remove the generator script and corresponding call in Makefile, all
derivatives should be migrated to binman in order to provide binary
images.
Since the mxs_nand_spl has implemented adjust read offset in
nand_spl_load_image, so we don't need to check the bad block in
nand_spl_adjust_offset. Directly return the offset to continue
read by nand_spl_load_image.
Ye Li [Tue, 17 Aug 2021 09:10:35 +0000 (17:10 +0800)]
arm: imx8m: Fix pad DSE issue for i.MX8MM/MN/MP
According to 8MM/MN/MP reference manual, their pad registers only have
4 valid DSE values. And DSE2 and DSE4 are different with current
definitions in iomux-v3.h. Fix the issue to align with manual.
Signed-off-by: Ye Li <ye.li@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
Ye Li [Tue, 17 Aug 2021 09:09:20 +0000 (17:09 +0800)]
mmc: fsl_esdhc_imx: Fix clock disable issue
The SD clock disable is wrapped by MMC_SUPPORTS_TUNING. So it
only works when UHS is enabled. However, in SD initialization the
power cycle does not depends on UHS. But the power cycle needs
disable the SD clock before power down.
So this causes a problem when UHS is not enabled. Some cards can't
become ready (ACMD14 timeout) due to the clock is enabled during
power cycle.
Signed-off-by: Ye Li <ye.li@nxp.com> Reviewed-by: Haibo Chen <haibo.chen@nxp.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Heiko Schocher [Tue, 17 Aug 2021 06:17:18 +0000 (08:17 +0200)]
imx: spl: fix imx8m secure boot
cherry-picked from NXP code: 719d665a87c6: ("MLK-20467 imx8m: Fix issue for booting signed image through uuu")
which fixes secure boot on imx8m based boards. Problem was
that FIT header and so IVT header too, was loaded to
memallocated address. So the ivt header address coded
in IVT itself does not fit with the real position.
Signed-off-by: Heiko Schocher <hs@denx.de> Tested-by: Tim Harvey <tharvey@gateworks.com>
Tom Rini [Wed, 22 Sep 2021 18:50:39 +0000 (14:50 -0400)]
Convert CONFIG_NAND_OMAP_ECCSCHEME to Kconfig
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Tom Rini [Wed, 22 Sep 2021 18:50:37 +0000 (14:50 -0400)]
Convert CONFIG_NAND_FSL_ELBC et al to Kconfig
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Tom Rini [Wed, 22 Sep 2021 18:50:35 +0000 (14:50 -0400)]
nand.h: Cleanup linux/mtd/rawnand.h usage
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Tom Rini [Wed, 22 Sep 2021 18:50:32 +0000 (14:50 -0400)]
Convert CONFIG_SYS_NAND_BAD_BLOCK_POS to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Tom Rini [Wed, 22 Sep 2021 18:50:27 +0000 (14:50 -0400)]
m53menlo: Switch to deriving CONFIG_SYS_NAND_PAGE_COUNT
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de> Cc: Olaf Mandel <o.mandel@menlosystems.com> Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 19 Sep 2021 21:14:49 +0000 (15:14 -0600)]
test: Allow hush tests to run in parallel
The -z tests don't really need to be part of the main set. Separate them
out so we can drop the test setup/cleans functions and thus run all tests
in parallel.
Simon Glass [Sun, 19 Sep 2021 21:14:48 +0000 (15:14 -0600)]
test: Allow vboot tests to run in parallel
Update the tests to use separate working directories, so we can run them
in parallel. It also makes it possible to see the individual output files
after the tests have completed.
test/py: Check hashes produced by mkimage against known values
Target code and mkimage share the same hashing infrastructure. If one
is wrong, it's very likely that both are wrong in the same way. Thus
testing won't catch hash regressions. This already happened in
commit 92055e138f28 ("image: Drop if/elseif hash selection in
calculate_hash()"). None of the tests caught that CRC32 was broken.
Instead of testing hash_calculate() against itself, create a FIT with
containing a kernel with pre-calculated hashes. Then check the hashes
produced against the known good hashes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Samuel Holland [Sat, 11 Sep 2021 22:05:53 +0000 (17:05 -0500)]
gpio: Factor out DT flag translation
The generic GPIO flags binding is shared across many drivers, some of
which need their own xlate function. Factor out the flag translation
code from gpio_xlate_offs_flags so it does not need to be duplicated.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Simon Glass <sjg@chromium.org>
arm: imx: mx7: Move CONFIG_OPTEE_TZDRAM_SIZE from lib/optee
This config is only used by three boards with this SOC. Most other
platforms derive this information from devicetree, and are unlikely
to ever need this config.
Moreover, it is confusing when Kconfig asks for this value under
"Support OPTEE images", but does not do anything with the value.
Move it to imx7 for those boards who still make use of it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
This value is not used by u-boot, and it should not. The load address
of an OPTEE image is defined by said image. Either a uImage or a FIT
will have a defined load address and entry point. Those values are the
correct ones, not CONFIG_OPTEE_LOAD_ADDR.
Commit f25006b96e9f ("optee: Add CONFIG_OPTEE_LOAD_ADDR") justifies
this config by requiring its presence in u-boot's .config for other
images as part of a larger build, claiming it is "the best way".
This argument is not persuasive. U-boot's configuration is driven by
platform requirements, not the other way around. It seems more likely
that the argument is conflating tooling issues with Kconfig. Yocto and
buildroot have excellent mechanisms for defining values across the
board (pun intended). u-boot's Kconfig is the wrong place to do it.
Furthermore, it is not "best" for u-boot because it hardcodes a value
which is then not used. In fact the load address that u-boot uses is
the one derived from the OPTEE image.
Confused yet? I sure was. To prevent future confusion, remove
CONFIG_OPTEE_LOAD_ADDR.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
It is no longer used in u-boot. Information about the TZDRAM location
is usually available in the devicetree as "/reserved-memory/" nodes.
Because this isn't used, remove it.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
lib: optee: Avoid CONFIG_TZDRAM_* in optee_verify_bootm_image()
The configs TZDRAM_BASE and TZDRAM_SIZE are expected to describe the
memory allocated to the OPTEE region. according to according to commit c5a6e8bd00cc ("optee: Add optee_verify_bootm_image()"). The TZDRAM is
with some limitations, described by "/reserved-memory" nodes in the
devicetree.
Consequently TZDRAM_BASE and TZDRAM_SIZE can point to imaginary
regions which have nothing to do with actual DRAM. They are not used
to configure the hardware or set up the Trust Zone Controller (TZC)
for OP-TEE -- the devicetree values are used instead.
When a valid OP-TEE image does not fall within the region described by
these configs, u-boot will refuse to load it. In fact, it mostly
serves to cause "bootm" to reject perfectly good OP-TEE images.
Ironically, someone has to correctly configure the devicetree for
TZDRAM, then go back and enter the same information in Kconfig for
"bootm". To remedy this, do not use TZDRAM_BASE and TZDRAM_SIZE in the
verification of OPTEE images.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The configuration CONFIG_OPTEE is defined 2 times:
1- in lib/optee/Kconfig for support of OPTEE images loaded by bootm command
2- in drivers/tee/optee/Kconfig for support of OP-TEE driver.
It is abnormal to have the same CONFIG define for 2 purpose;
and it is difficult to managed correctly their dependencies.
Moreover CONFIG_SPL_OPTEE is defined in common/spl/Kconfig
to manage OPTEE image load in SPL.
This definition causes an issue with the macro CONFIG_IS_ENABLED(OPTEE)
to test the availability of the OP-TEE driver.
This patch cleans the configuration dependency with:
- CONFIG_OPTEE_IMAGE (renamed) => support of OP-TEE image in U-Boot
- CONFIG_SPL_OPTEE_IMAGE (renamed) => support of OP-TEE image in SPL
- CONFIG_OPTEE (same) => support of OP-TEE driver in U-Boot
- CONFIG_OPTEE_LIB (new) => support of OP-TEE library
After this patch, the macro have the correct behavior:
- CONFIG_IS_ENABLED(OPTEE_IMAGE) => Load of OP-TEE image is supported
- CONFIG_IS_ENABLED(OPTEE) => OP-TEE driver is supported
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Marek Vasut [Tue, 14 Sep 2021 03:21:48 +0000 (05:21 +0200)]
mtd: cqspi: Fix division by zero
Both dummy.nbytes and dummy.buswidth may be zero. By not checking
the later, it is possible to trigger division by zero and a crash.
This does happen with tiny SPI NOR framework in SPL. Fix this by
adding the check and returning zero dummy bytes in such a case.
Fixes: 38b0852b0ea ("spi: cadence-qspi: Add support for octal DTR flashes") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Jagan Teki <jagan@amarulasolutions.com> Cc: Vignesh R <vigneshr@ti.com> Cc: Pratyush Yadav <p.yadav@ti.com>
[trini: Drop Pratyush's RB as his requested changes weren't made as
Marek disagreed]
Jan Kiszka [Sat, 18 Sep 2021 06:17:55 +0000 (08:17 +0200)]
watchdog: rti_wdt: Add support for loading firmware
To avoid the need of extra boot scripting on AM65x for loading a
watchdog firmware, add the required rproc init and loading logic for the
first R5F core to the watchdog start handler. In case the R5F cluster is
in lock-step mode, also initialize the second core. The firmware itself
is embedded into U-Boot binary to ease access to it and ensure it is
properly hashed in case of secure boot.
One possible firmware source is https://github.com/siemens/k3-rti-wdt.
The board is responsible for providing the firmware as additional
loadable via the U-Boot fit image. The driver will pick up its location
from /fit-images/k3-rti-wdt-firmware then.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
projects / u-boot.git / log
;st=author){kind=link}
![3 years agoimx8m: Restrict usable memory based on rom_pointer[0]](/%22/img/sics.gif/%22/static/git-favicon.png?p=u-boot.git;a=commit;h=5a6af8c19ab8c9a7dd44db9406b68fcb7fe5ee18){kind=link}
