Michal Simek [Wed, 28 Jun 2017 13:40:32 +0000 (15:40 +0200)]
arm64: zynqmp: Fix SVD mask for getting chip ID
Mask should start from the first bit - using 0xe is just wrong.
3bits are used that's why 0x7 mask is correct.
This patch is fixing silicon ID code detection. Previous behavior was
that bit0 was completely ignored.
Issue was found on 2eg chip detection.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
arm64: zynqmp: Remove ifdef around zynqmp mmio read and write rotuines
This patch removes ifdef around mmio read and write rotuines
and make them a single routine by checking the current el.
This patch helps to remove ifdef around invoke_smc as well.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
fpga: xilinx: Avoid using local intermediate buffer
Dont use local temporary buffer for printing out the
info instead use directly from memroy. This fixes the
issue of stack corruprion due to local buffer overflow.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for CCF, this CCF reads the ref clocks
from dt and checks all the required clock control
registers for its source , divisors and calculates
the clock from them. This supports clock and set
functions.
Panic when read/write fails.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Alexander Graf [Mon, 3 Jul 2017 11:41:36 +0000 (13:41 +0200)]
zynq: Add Z-Turn board
The Z-Turn board is a low cost development board based on the
Xilinx Zynq SoC. While it's powerful and quite versatile, it
so far lacked upstream support.
This patch adds basic support for the Z-Turn. It does however
for now miss enablement for MIO51 reset which means that USB
and ethernet don't work. For that either FSBL or SPL need to
be adjusted. The SPL part will follow later.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Alexander Graf [Mon, 3 Jul 2017 11:41:35 +0000 (13:41 +0200)]
zynq: Enable distro boot
Distro boot allows devices to boot using standardized boot methods by
default. This can be very handy for distributions that want to run on
different platforms.
This patch moves the zynq platform to use its old, zynq specific boot
method first and then fall back to distro boot. That way supporting
Linux distributions like openSUSE is much easier.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Alexander Graf [Mon, 3 Jul 2017 11:41:34 +0000 (13:41 +0200)]
zynq: Add EFI runtime sections to linker script
When using EFI_LOADER, we add a few special sections for runtime code and
data which get relocated on demand when executing a target OS.
These runtime structures need to get annotated properly in the linker script.
While we do that properly in the generic one, we missed out on the zynq
specific linker script.
This patch adds the EFI runtime section annotations into the zynq linker script
so that the efi loader code actually works on that platform.
Signed-off-by: Alexander Graf <agraf@suse.de> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Simon Glass [Thu, 27 Jul 2017 15:31:04 +0000 (09:31 -0600)]
dm: console: Check for serial devices properly
With driver model the serial device is often not called "serial". Mark
driver-model stdio devices so that they can be detected and we can look up
the uclass. This is a more reliable way of finding out whether the console
is connected to a serial device or not.
Tom Rini [Wed, 26 Jul 2017 17:11:36 +0000 (13:11 -0400)]
am335x_hs_evm: Disable CONFIG_SPL_ENV_SUPPORT
The main uses of CONFIG_SPL_ENV_SUPPORT are for network support and for
disabling "Falcon Mode" support at run-time. As this build enables
neither, remove this feature.
Cc: Andrew F. Davis <afd@ti.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 27 Jul 2017 01:48:00 +0000 (21:48 -0400)]
env: Migrate CONFIG_ENV_IS_IN_FAT options to Kconfig
We rename the various FAT_ENV_xxx options to CONFIG_ENV_FAT_xxx so that
they can be modified via Kconfig. Migrate all existing users to the new
values.
Alexander Graf [Mon, 31 Jul 2017 07:15:57 +0000 (09:15 +0200)]
efi_loader: Fix warning in efi_gop
Commit ca9193d2b16 ("efi_loader: gop: fixes for CONFIG_DM_VIDEO without
CONFIG_LCD") dropped the explicit (void*) cast for fb_base in efi gop support
for CONFIG_LCD without DM. This patch adds it back, eliminating the now occuring
warning again
Fixes: ca9193d2b16 ("efi_loader: gop: fixes for CONFIG_DM_VIDEO without CONFIG_LCD") Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Alexander Graf <agraf@suse.de>
Tom Rini [Mon, 31 Jul 2017 11:27:45 +0000 (07:27 -0400)]
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2017-07-29
A lot of EFI greatness this time around. Thanks a lot to the
two amazing new contributors
Heinrich Schuchardt and
Rob Clark
we now gain
- stable objects across multiple bootefi invocations
- fixes for shim
- fixes for ipxe
- protocol installation
- device path conversion to/from text
- working "lsefi" support in grub
- working notifiers
- various bug fixes
Stefan Roese [Tue, 18 Jul 2017 12:10:49 +0000 (14:10 +0200)]
x86: dfi-bt700: Add xHCI USB support
Change from EHCI to xHCI on the DFI BayTrail SoM.
The xHCI USB hub is connected to an GPIO on the DFI BayTrail SoM. For
correct operation, it needs to get reset upon power-up. Otherwise it
may happen that the hub is not detected after a software reboot. This
patch also configures this GPIO in the dts for correct operation.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This config option is needed on the congatec x86 BayTrail board, as
otherwise the USB hub will not get initialized correctly. This
patch selects this Kconfig option again.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Stefan Roese [Tue, 18 Jul 2017 12:10:41 +0000 (14:10 +0200)]
x86: theadorable-x86-dfi-bt700: Add Spansion SPI support and move VIDEO blob
To support the Spansion SPI NOR flashes, this patch enables the support in
defconfig. This increases the U-Boot binary too much so that it does
not fit into its area in the ROM. So also move the VIDEO BIOS blob
a bit to make some space here.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Thu, 6 Jul 2017 11:41:53 +0000 (14:41 +0300)]
x86: Add Intel Edison board files
Add Intel Edison board which is using U-Boot.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <aiden.park@intel.com>
Dukjoon Jeon <dukjoon.jeon@intel.com>
eric.park <eric.park@intel.com>
Fabien Chereau <fabien.chereau@intel.com>
Felipe Balbi <felipe.balbi@linux.intel.com>
Scott D Phillips <scott.d.phillips@intel.com>
Sebastien Colleur <sebastienx.colleur@intel.com>
Steve Sakoman <steve.sakoman@intel.com>
Vincent Tinelli <vincent.tinelli@intel.com>
In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.
First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).
Serial number (serial# environment variable) is generated based on eMMC
CID.
MAC address on USB network interface is unique to the board but kept the
same all over the time.
Set mac address from U-Boot using following scheme:
OUI = 02:00:86
next 3 bytes of MAC address set from eMMC serial number
This allows to have a unique mac address across reboot and flashing.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: Add MAINTAINERS file for Intel Edison board] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Felipe Balbi [Thu, 6 Jul 2017 11:41:52 +0000 (14:41 +0300)]
x86: Add Intel Tangier support
Add Intel Tangier SoC support.
Intel Tangier SoC is a core part of Intel Merrifield platform. For
example, Intel Edison board is based on such platform.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <aiden.park@intel.com>
Dukjoon Jeon <dukjoon.jeon@intel.com>
eric.park <eric.park@intel.com>
Fabien Chereau <fabien.chereau@intel.com>
Scott D Phillips <scott.d.phillips@intel.com>
Sebastien Colleur <sebastienx.colleur@intel.com>
Steve Sakoman <steve.sakoman@intel.com>
Vincent Tinelli <vincent.tinelli@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Andy Shevchenko [Thu, 6 Jul 2017 11:41:51 +0000 (14:41 +0300)]
x86: Add dma-mapping.h to architectural code
Some cross-platform drivers rely on this header present.
Make it so for x86.
It's just a copy'n'paste of arch/arm/include/asm/dma-mapping.h.
Suggested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Felipe Balbi [Wed, 5 Jul 2017 17:33:20 +0000 (20:33 +0300)]
watchdog: Introduce watchdog driver for Intel Tangier
Add watchdog driver for Intel Tangier based platforms.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Andy Shevchenko [Tue, 4 Jul 2017 16:32:22 +0000 (19:32 +0300)]
arch/x86: Select USB before selecting host driver
Kbuild complains if USB is not selected before any of host driver.
warning: (X86) selects USB_EHCI_HCD which has unmet direct dependencies (USB)
warning: (X86) selects USB_EHCI_HCD which has unmet direct dependencies (USB)
Select it for X86.
Fixes: 64d6ac5bc4a9 ("Kconfig: USB: Migrate CONFIG_USB_EHCI_HCD users to Kconfig") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[bmeng: Update all x86 boards' defconfig files to remove CONFIG_USB] Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Rob Clark [Thu, 27 Jul 2017 12:04:19 +0000 (08:04 -0400)]
efi_loader: indent entry/exit prints to show nesting level
This should make it easier to see when a callback back to UEFI world
calls back in to the u-boot world, and generally match up EFI_ENTRY()
and EFI_EXIT() calls.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[agraf: remove static from const var] Signed-off-by: Alexander Graf <agraf@suse.de>
Fix following warnings encountered with platforms
dra7xx_evm and dra7xx_hs_evm :
arm: + dra7xx_evm
+ hccr = (struct xhci_hccr *)devfdt_get_addr(dev);
+ ^
+ hcor = (struct xhci_hcor *)((phys_addr_t)hccr +
+ ^
w+drivers/usb/host/xhci-dwc3.c: In function 'xhci_dwc3_probe':
w+drivers/usb/host/xhci-dwc3.c:124:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
w+drivers/usb/host/xhci-dwc3.c:125:30: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
w+drivers/usb/host/xhci-dwc3.c:125:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
arm: + dra7xx_hs_evm
+ hccr = (struct xhci_hccr *)devfdt_get_addr(dev);
+ ^
+ hcor = (struct xhci_hcor *)((phys_addr_t)hccr +
+ ^
w+drivers/usb/host/xhci-dwc3.c: In function 'xhci_dwc3_probe':
w+drivers/usb/host/xhci-dwc3.c:124:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
w+drivers/usb/host/xhci-dwc3.c:125:30: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
w+drivers/usb/host/xhci-dwc3.c:125:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Introduced by 7e65e84 usb: host: xhci-dwc3: Convert driver to DM
This driver is used to stub PHY operations in a driver (USB, SATA).
This is useful when the 'client' driver (USB, SATA, ...) uses the PHY
framework and there is no actual PHY harwdare to drive.
Add CONFIG_DM_USB flag to avoid following compilation errors
detected by buildman :
+drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
+drivers/usb/host/xhci-dwc3.c:168: undefined reference to `xhci_deregister'
+drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
+drivers/usb/host/xhci-dwc3.c:145: undefined reference to `usb_get_dr_mode'
+drivers/usb/host/xhci-dwc3.c:152: undefined reference to `xhci_register'
introduced by patch d5c3f014da3 "usb: host: xhci-dwc3: Convert driver to DM"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reported-by: Ran Wang <ran.wang_1@nxp.com>
Cc: Ran Wang <ran.wang_1@nxp.com> Cc: Bin Meng <bmeng.cn@gmail.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reported-by: Ran Wang <ran.wang_1@nxp.com>
Patrick Delaunay [Wed, 19 Jul 2017 14:39:25 +0000 (16:39 +0200)]
dfu: add common function to initiate transaction
- factorize code between read and write transaction
- always use dfu_transaction_cleanup() to initialize
the internal variable: easy maintenance
- replace direct access by dfu_get_buf() and dfu_get_buf_size()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Patrick Delaunay [Wed, 19 Jul 2017 14:39:22 +0000 (16:39 +0200)]
dfu: allow dfu read on partition greater than 2GB
solve issue on get_medium_size() function
the detection of error is a simple test < 0
but for ARM platform, long is 32bits and 2GB = 0x80000000
is seen as error.
I solve the issue by changing the prototype fo the function
to separate size and result.
This patch prepare the next patch with size change to u64.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Bin Meng [Wed, 19 Jul 2017 13:51:21 +0000 (21:51 +0800)]
usb: xhci: Enable TT to support LS/FS devices behind a HS hub
So far LS/FS devices directly attached to xHC root port can be
successfully enumerated by xHCI driver, but if they are connected
behind a hub, the enumeration process fails to address the device.
It turns out xHCI driver still misses a part that in the device's
input slot context, all Transaction Translator (TT) related fields
are not programmed. The xHCI spec defines how to enable TT.
Now LS/FS devices like USB keyboard/mouse can be enumerated behind
a high speed hub.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
There is no way to know whether the attached device is a hub or
not in advance before the device's descriptor is fetched. But
once we know it's a high speed hub, per the xHCI spec, we need
to tell xHC it's a hub device by initializing hub-related fields
in the input slot context.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:51:17 +0000 (21:51 +0800)]
dm: usb: Add a new USB controller operation 'update_hub_device'
For USB host controllers like xHC, its internal representation of
hub needs to be updated after the hub descriptor is fetched. This
adds a new op that does this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:51:16 +0000 (21:51 +0800)]
usb: hub: Parse and save TT details from device descriptor
A high speed hub has a special responsibility to handle full speed/
low speed devices connected on downstream ports. In this case, the
hub must isolate the high speed signaling environment from the full
speed/low speed signaling environment with the help of Transaction
Translator (TT). TT details are provided by hub descriptors and we
parse and save it to hub uclass_priv for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:51:15 +0000 (21:51 +0800)]
usb: xhci: Program 'route string' in the input slot context
xHCI spec says: the values of the 'route string' field shall be
initialized by the first 'Address Device' command issued to a
device slot, and shall not be modified by any other command.
So far U-Boot does not program this field, and it does not prevent
SS device directly attached to root port, or HS device behind an HS
hub, from working, due to the fact that 'route string' is used by
the xHC to target SS packets. But in order to enumerate devices
behind an SS hub, this field must be programmed.
With this commit and along with previous commits, now SS & HS devices
attached to a USB 3.0 hub can be enumerated by U-Boot.
As usual, this new feature is only available when DM is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
For future extension, change xhci_setup_addressable_virt_dev()
signature to accept a pointer to 'struct usb_device', instead
of its members slot_id & speed, as the struct already contains
these two plus some other useful information of the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:51:13 +0000 (21:51 +0800)]
usb: hub: Support 'set hub depth' request for USB 3.0 hubs
USB 3.0 hub uses a hub depth value multiplied by four as an offset
into the 'route string' to locate the bits it uses to determine the
downstream port number. We shall set the hub depth value of a USB
3.0 hub after it is configured.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:51:12 +0000 (21:51 +0800)]
usb: hub: Translate USB 3.0 hub port status into old version
USB 3.0 hub port status field has different bit positions from 2.0
hubs. Since U-Boot only understands the old version, translate the
new one into the old one.
Since we are going to add USB 3.0 hub support, this feature is only
available with driver model USB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:51:11 +0000 (21:51 +0800)]
usb: hub: Add a new API to test if a hub device is root hub
Sometimes we need know if a given hub device is root hub or not.
Add a new API to test this. This removes the xHCI driver's own
version is_root_hub() and change to use the new API.
While we are here, remove the unused/commented out get_usb_device()
in the xHCI driver too.
Bin Meng [Wed, 19 Jul 2017 13:51:09 +0000 (21:51 +0800)]
usb: hub: Use 'struct usb_hub_device' as hub device's uclass_priv
Use USB hub device's dev->uclass_priv to point to 'usb_hub_device'
so that with driver model usb_hub_reset() and usb_hub_allocate()
are no longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Bin Meng [Wed, 19 Jul 2017 13:50:10 +0000 (21:50 +0800)]
x86: minnowmax: Enable USB xHCI support
BayTrail SoC supports both EHCI and xHCI controllers. However only
one host controller (either EHCI or xHCI) can be used. To enable
HSIC and SS ports, xHCI must be used. This turns on xHCI support on
Intel MinnowMax board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:09 +0000 (21:50 +0800)]
x86: minnowmax: Add a environment variable for USB power-on delay
Occasionally it was observed that on Intel MinnowMax board, with a
USB 2.0 device connected to the bottom port, when doing 'usb start'
on the xHCI controller:
scanning bus 0 for devices... cannot reset port 3!?
But neither of the two USB ports is routed to xHCI root port 3.
Adding some debug information shows that xHCI port 3 PORTSC register
mysteriously reports both CCS = 1 and CSC = 1.
This is not seen every time. After increasing the timeout to wait
for power to become stable, the issue is gone. So this indicates
current default USB power-on delay (20ms) might be at a critical
region where power is stable/unstable. U-Boot provides a mechanism
to have a environment variable to override the default one. Add
one for MinnowMax.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:08 +0000 (21:50 +0800)]
usb: xhci: Convert CONFIG_USB_XHCI_PCI to Kconfig
Add CONFIG_USB_XHCI_PCI as a Kconfig option.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:07 +0000 (21:50 +0800)]
usb: cmd: Print actual packet size for super speed devices
USB 3.0 defines bMaxPacketSize0 field in the device descriptor as
the exponent of 2, so let's print the calculated actual size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:06 +0000 (21:50 +0800)]
configs: Remove CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS in all boards
Now that EHCD does not use CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:05 +0000 (21:50 +0800)]
usb: ehci: Get rid of CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS
EHC reports supported maximum number of ports in the HCSPARAMS
register, so it's unnecessary to use a hardcoded config option
CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:04 +0000 (21:50 +0800)]
configs: Remove CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS in all boards
Now that xHCD does not use CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS,
remove it in all boards' config files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:03 +0000 (21:50 +0800)]
usb: xhci: Get rid of CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS
xHC reports supported maximum number of ports in the HCSPARAMS1
register, so it's unnecessary to use a hardcoded config option
CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:02 +0000 (21:50 +0800)]
usb: xhci: Change MAX_HC_PORTS to 255
HCSPARAMS1:MaxPorts field specifies the maximum port number value,
and its valid values are in the range of 1 to 255.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:01 +0000 (21:50 +0800)]
usb: hub: Add 3.0 hub port status mask of 2.0 hub
USB 3.0 hub port status has different bit position regarding to
port power, port speed, etc. But others are the same as 2.0 hubs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:50:00 +0000 (21:50 +0800)]
usb: hub: Change USB hub descriptor to match USB 3.0 hubs
USB 3.0 hubs have a slightly different hub descriptor than USB 2.0
hubs, with a fixed (rather than variable length) size. Change the
host controller drivers that access those last two fields
(DeviceRemovable and PortPowerCtrlMask) to use the union.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:49:59 +0000 (21:49 +0800)]
usb: hub: Revise wLength for 'get port status' request
For accuracy, we should use 'sizeof(struct usb_port_status)' as the
wLength for 'get port status' request, although it happens to be
equal to 'sizeof(struct usb_hub_status)'.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:49:58 +0000 (21:49 +0800)]
usb: hub: Send correct wValue to get hub descriptor of a USB 3.0 hub
Testing a USB 3.0 hub by connecting it to the xHCI port on Intel
MinnowMax, when issuing 'get hub descriptor' to the hub, xHCI
reports a transfer event TRB with a completion code 6 which means
'Stall Error'.
In fact super speed USB hub descriptor type is 0x2a, not 0x29.
Sending correct SETUP packet to the hub makes it not stall anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:49:57 +0000 (21:49 +0800)]
usb: hub: Update handling connect status/change in usb_scan_port()
It was observed that on Intel MinnowMax board, when xHCI is enabled
in the BayTrail SoC, with a USB 3.0 device connected to the bottom
USB 3.0 port (mapped to xHCI root port #7), its PORTSC register is
always 0x201203 (CCS = 1, CSC = 0). The root cause of such behavior
is unknown yet. Connect status change bit is set on the same port
with a USB 2.0 device (mapped to xHCI port #1, which is a different
port on the root hub).
With current logic in usb_scan_port(), the enumeration process will
abort if it does not detect a connect status change on a hub port.
However since a device connection status is correctly reported, the
enumeration process can still continue.
With this change, USB device connected to the bottom blue port on
MinnowMax board can be enumerated under either SS or HS mode.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de> Tested-by: Dinh Nguyen <dinguyen@kernel.org>
Bin Meng [Wed, 19 Jul 2017 13:49:56 +0000 (21:49 +0800)]
usb: xhci: Add input slot context in xhci_set_configuration()
A valid input slot context for a 'configure endpoint' command requires
the 'Context Entries' field to be initialized to the index of the last
valid endpoint context that is defined by the target configuration. We
set up the 'Context Entries' field, but we forget to include the input
slot context in the input control context 'Add Context flags' bitmap.
So xHC will simply ignore input slot context and continue using its own
which contains old information of the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:49:55 +0000 (21:49 +0800)]
usb: xhci: Initialize scratchpad buffer array and scratchpad buffers
The scratchpad buffer array is used to define the locations of
statically allocated memory pages that are available for the
private use of the xHC. The xHCI spec explicitly mentions that
system software shall allocate the scratchpad buffers before
placing the xHC in to Run mode (Run/Stop (R/S) = ‘1’), however
U-Boot is missing this part.
This causes xHC on Intel platform does not respond the very first
'enable slot' command that is given to xHC and the 'enable slot'
command completion event TRB is never generated and xHC seems to
hang forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
In xhci_queue_command(), when the command is not 'reset endpoint',
'stop endpoint' or 'set TR dequeue pointer', endpoint ID should not
be encoded in the TRB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
Bin Meng [Wed, 19 Jul 2017 13:49:53 +0000 (21:49 +0800)]
usb: xhci: Remove incorrect comments for struct xhci_container_ctx
There is no member called 'dma' in struct xhci_container_ctx. Remove
the comments that mentions it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de>
projects / u-boot.git / log
