Samuel Holland [Sat, 28 Aug 2021 16:49:03 +0000 (11:49 -0500)]
sunxi: Remove non-DM MMC pin setup
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 21:51:03 +0000 (16:51 -0500)]
pinctrl: sunxi: Add MMC pinmuxes
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 04:01:29 +0000 (23:01 -0500)]
i2c: sun8i_rsb: Only do non-DM pin setup for non-DM I2C
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.
Clean up the code in the process: remove #ifdefs and recognize that the
pin configuration is the same for all sun8i/sun50i SoCs, not just those
which select CONFIG_MACH_SUN8I.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 04:01:29 +0000 (23:01 -0500)]
i2c: sun6i_p2wi: Only do non-DM pin setup for non-DM I2C
When the DM_I2C driver is loaded, the pin setup is done automatically
from the device tree by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Thu, 21 Oct 2021 03:55:06 +0000 (22:55 -0500)]
sunxi: Remove options and setup code for I2C2-I2C4
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 20:17:32 +0000 (15:17 -0500)]
pinctrl: sunxi: Add I2C pinmuxes
Where multiple options were available, the one matching board.c and the
device trees was chosen.
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fixup H5 I2C1 pinmux] Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 16:49:40 +0000 (11:49 -0500)]
net: sun8i_emac: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 18:34:29 +0000 (13:34 -0500)]
pinctrl: sunxi: Add sun8i EMAC pinmuxes
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 18:16:44 +0000 (13:16 -0500)]
sunxi: Remove non-DM GMAC pin setup
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 18:13:52 +0000 (13:13 -0500)]
pinctrl: sunxi: Add sunxi GMAC pinmuxes
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 18:22:41 +0000 (13:22 -0500)]
net: sunxi_emac: Remove non-DM pin setup
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 18:21:36 +0000 (13:21 -0500)]
pinctrl: sunxi: Add sun4i EMAC pinmuxes
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Sat, 28 Aug 2021 18:00:45 +0000 (13:00 -0500)]
pinctrl: sunxi: Add UART pinmuxes
This includes UART0 and R_UART (s_uart) on all supported platforms, plus
the additional UART configurations from arch/arm/mach-sunxi/board.c.
Pin lists and mux values were taken from the Linux drivers.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Tue, 17 Aug 2021 05:52:00 +0000 (00:52 -0500)]
sunxi: pinctrl: Implement get_pin_muxing function
The pinmux command uses this function to display pinmux status.
Since the driver cannot map pin numbers to a list of supported
functions, only functions which are common across all pins can be
reported by name.
Signed-off-by: Samuel Holland <samuel@sholland.org> Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Tue, 17 Aug 2021 04:56:47 +0000 (23:56 -0500)]
sunxi: pinctrl: Implement pin muxing functions
Implement the operations to get pin and function names, and to set the
mux for a pin. The pin count and pin names are calculated as if each
bank has the maximum number of pins. Function names are simply the index
into a list of { function name, mux value } pairs.
We assume all pins associated with a function use the same mux value for
that function. This is generally true within a group of pins on a single
port, but generally false when some peripheral can be muxed to multiple
ports. For example, A64 UART3 uses mux 3 on port D, and mux 2 on port H.
But all of the port D pins use the same mux value, and so do all of the
port H pins. This applies even when the pins for some function are not
contiguous, and when the lower-numbered mux values are unused. A good
example of both of these cases is SPI0 on most SoCs.
This strategy saves a lot of space (which is especially important for
SPL), but where the mux value for a certain function differs across
ports, it forces us to choose a single port for that function at build
time. Since almost all boards use the default (i.e. reference design)
pin muxes[1], this is unlikely to be a problem.
[1]: See commit dda9fa734f81 ("sunxi: Simplify MMC pinmux selection")
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: add comment summarising the commit message] Reviewed-by: Andre Przywara <andre.przywara@arm.com> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Samuel Holland [Fri, 13 Aug 2021 01:09:43 +0000 (20:09 -0500)]
sunxi: pinctrl: Create the driver skeleton
Create a do-nothing driver for each sunxi pin controller variant.
Since only one driver can automatically bind to a DT node, since the
GPIO driver already requires a manual binding process, and since the
pinctrl driver needs access to some of the same information, refactor
the GPIO driver to be bound by the pinctrl driver. This commit should
cause no functional change.
Signed-off-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
If include/generated/env.in does not exist, which is a typical case for
clean build, quiet_cmd_gen_envp command tries to delete this file
unconditionally.
This produces following warning during the build:
ENVP include/generated/env.in
rm: cannot remove 'include/generated/env.in': No such file or directory
Add '-f' option to the `rm` command to not complain if file does not
exist.
Fixes: f432eb6d8a9d ("env: Avoid using a leftover text-environment file") Reviewed-by: Sean Anderson <seanga2@gmail.com> Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
ARM: dts: colibri-imx6ull: fix mac address passing
colibri-imx6ull ethernet device is fec2, while the optional secondary
ethernet is fec1, update the ethernet aliases in the .dts file so that
ethaddr is set to fec2 and eth1addr to fec1.
Without this change the ethernet interfaces have a different
mac address between Linux and U-Boot.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Simon Glass [Sat, 12 Mar 2022 05:37:23 +0000 (22:37 -0700)]
env: Avoid using a leftover text-environment file
If include/generated/environment.h exists (perhaps leftover from a build
of another board) it is used, even if the board currently being built does
not have a text environment.
This causes a build error. Fix it by emptying the file if it should not be
there.
Fixes: https://source.denx.de/u-boot/u-boot/-/issues/9 Signed-off-by: Simon Glass <sjg@chromium.org> Reported-by: Sean Anderson <seanga2@gmail.com> Tested-by: Sean Anderson <seanga2@gmail.com>
Andy Shevchenko [Wed, 30 Mar 2022 09:14:43 +0000 (12:14 +0300)]
efi_loader: initrddump: Actually use the custom CFLAGS
It seems a copy'n'paste typo when tool had been introduced.
It has never had the 'exit' suffix in the file name. Hence,
the custom CFLAGS never been applied and, for example, BFD
linker complains:
LD lib/efi_loader/initrddump_efi.so
ld.bfd: lib/efi_loader/initrddump.o: warning: relocation in read-only section `.text.efi_main'
ld.bfd: warning: creating DT_TEXTREL in a shared object
Remove wrong 'exit' suffix from the custom CFLAGS variable.
Fixes: 65ab48d69ddb ("efi_selftest: provide initrddump test tool") Fixes: 9c045a49a9c9 ("efi_loader: move dtbdump.c, initrddump.c to lib/efi_loader") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Bin Meng [Mon, 28 Mar 2022 02:43:50 +0000 (10:43 +0800)]
doc: usage: Update vxworks doc to mention RISC-V support
At present the doc only mentions Arm, PowerPC and x86. RISC-V support
has been added since VxWorks SR0650 support for a while, and U-Boot
supports loading a RISC-V VxWorks kernel too. Let's document it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Patrick Delaunay [Tue, 29 Mar 2022 14:01:13 +0000 (16:01 +0200)]
doc: mmc dev
Provide human readable descriptions of the speed nodes instead of the name
of constants from the code as it is already done for 'mmc rescan'
command in commit 212f078496e4 ("doc: mmc rescan speed mode").
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Aswath Govindraju <a-govindraju@ti.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sughosh Ganu [Sun, 13 Mar 2022 14:47:58 +0000 (20:17 +0530)]
qemu: arm: Remove platform specific function to get RNG device
The QEMU platform has a function defined to get the random number
generator(RNG) device. However, the RNG device can be obtained simply
by searching for a device belonging to the RNG uclass. Remove the
superfluous platform function defined for the QEMU platform for
getting the RNG device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org> Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Thu, 31 Mar 2022 12:28:43 +0000 (08:28 -0400)]
Merge branch '2022-03-31-critical-fixes'
- Fixes for 2 gateworks platforms, Edison platform, incorrectly showing
2 logos on LCD screens, not cleaning a generated environment file and
correct the CONFIG_SYS_IMMR Kconfig migration on a number of MPC85xx
platforms.
Tim Harvey [Wed, 30 Mar 2022 20:39:02 +0000 (13:39 -0700)]
board: gateworks: venice: determine dram size at runtime
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Tom Rini [Wed, 30 Mar 2022 13:30:15 +0000 (09:30 -0400)]
powerpc: Fix incorrect SYS_IMMR migration values
When migrating SYS_IMMR, I didn't allow for boards to provide
non-default values here. This lead to an incorrect migration on the
platforms where CONFIG_SYS_IMMR is set to CONFIG_SYS_CCSRBAR and
CONFIG_SYS_CSSRBAR is NOT the same as CONFIG_SYS_CCSRBAR_DEFAULT. Add
text to the prompt so that non-default values can be used and re-migrate
the platforms that have CONFIG_SYS_IMMR=CONFIG_SYS_CSSRBAR where
CONFIG_SYS_CSSRBAR != CONFIG_SYS_CCSRBAR_DEFAULT.
Fixes: be7dbb60c5bf ("Convert CONFIG_SYS_IMMR to Kconfig") Reported-by: Pali Rohár <pali@kernel.org> Signed-off-by: Tom Rini <trini@konsulko.com> Tested-by: Pali Rohár <pali@kernel.org>
Makefile: make clean should delete include/generated/env.in
'make sifive_unamtched_defconfig; make clean; make' fails if file
include/generated/env.in exists. 'make clean' should remove all files that
stop building.
Add file include/generated/env.in to the clean target.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Reviewed-by: Marek Behún <marek.behun@nic.cz>
commit 7c84319af9c7 ("dm: gpio: Correct use of -ENODEV in drivers")
changed the return code for an I2C NAK from -ENODEV to -EREMOTEIO.
Update the gsc_i2c_read and gsc_i2c_write functions for this change
to properly retry the transaction on a NAK meaning the GSC is busy.
Fixes: 7c84319af9c7 ("dm: gpio: Correct use of -ENODEV in drivers") Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Marek Vasut [Mon, 21 Feb 2022 05:16:12 +0000 (06:16 +0100)]
arm: socfpga: vining: Fix mtdparts for 2x256 MiB SF variant
The 2x256 MiB SF variant of this system has 192 MiB rootfs MTD partition
containing UBI on SF0, use the correct size in U-Boot environment, else
U-Boot cannot mount UBI and boot on this variant.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com> Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Cc: Tien Fong Chee <tien.fong.chee@intel.com> Cc: Tom Rini <trini@konsulko.com>
Tim Harvey [Tue, 22 Mar 2022 18:42:49 +0000 (11:42 -0700)]
imx: ventana: enable ONFI detection to fix NAND chip configuration
Enable ONFI detection to fix NAND chip configuration. Without this
the NAND oobsize will be wrong which leads to invalid ECC strength and
incompatibility with the previous configuration.
Fixes: 777f333c375a ("imx: ventana: enable dm for MTD and NAND") Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Fabio Estevam <festevam@denx.de>
Han Xu [Fri, 25 Mar 2022 13:36:38 +0000 (08:36 -0500)]
mtd: gpmi: fix the bch setting backward compatible issue
Previous u-boot code changed the default bch setting behavior and caused
backward compatible issue. This fix choose the legacy bch geometry back
again as the default option. If the minimum ecc strength that NAND chips
required need to be chosen, it can be enabled by either adding DT flag
"fsl,use-minimum-ecc" or CONFIG_NAND_MXS_USE_MINIMUM_ECC in configs. The
unused flag "fsl,legacy-bch-geometry" get removed.
Fixes: 51cdf83eea (mtd: gpmi: provide the option to use legacy bch geometry) Fixes: 616f03daba (mtd: gpmi: change the BCH layout setting for large oob NAND) Tested-by: Tim Harvey <tharvey@gateworks.com> Tested-by: Sean Nyekjaer <sean@geanix.com> Signed-off-by: Han Xu <han.xu@nxp.com> Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mark Kettenis [Mon, 21 Mar 2022 21:41:18 +0000 (22:41 +0100)]
arm: apple: Fix mem layout
The current approach for setting the environment variables that
describe the memory layout runs the risk of overlapping with
reserved memory regions. Use the lmb code to derive the addresses
for these variables instead.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Up to now the initrddump.efi application has drained the input after
showing the prompt. This works for humans but leads to problems when
automating testing. If the input is drained, this should be done before
showing the prompt.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
efi_loader: nocolor command line attr for initrddump.efi
initrddump.efi uses colored output and clear the screen. This is not
helpful for integration into Python tests. Allow specifying 'nocolor' in
the load option data to suppress color output and clearing the screen.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Andre Przywara [Tue, 15 Mar 2022 23:20:54 +0000 (23:20 +0000)]
sunxi: dts: Update RGMII phy-mode properties
Commit f11513d99787 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Samuel Holland <samuel@sholland.org>
Andre Przywara [Tue, 15 Mar 2022 00:00:53 +0000 (00:00 +0000)]
sunxi: Fix old GMAC pinmux setup
Commit 5bc4cd05d7d4 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Pali Rohár [Wed, 23 Mar 2022 16:19:42 +0000 (17:19 +0100)]
arm: a37xx: espressobin: Fix non-working SPI
Commit 0934dddc6436 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke SPI support on some Espressobin boards and results in
following U-Boot error:
Loading Environment from SPIFlash... jedec_spi_nor flash@0: unrecognized JEDEC id bytes: f7, 30, 0b
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Before that commit DT node for SPI was called 'spi-flash@0' and after
that commit it is called 'flash@0'. Before that commit 'spi-max-frequency'
was set to 50000000 and after it is 104000000.
Rename DT node 'spi-flash@0 in armada-3720-espressobin-u-boot.dtsi to
'flash@0' and set custom U-Boot 'spi-max-frequency' back to 50000000.
With this change SPI is working on Espressobin again and it is detected
with JEDEC ids ef, 60, 16 on our tested unit.
Loading Environment from SPIFlash... SF: Detected w25q32dw with page size 256 Bytes, erase size 4 KiB, total 4 MiB
OK
Note that it is unknown why spi-max-frequency with value 104000000 does not
work in U-Boot as it works fine with Linux kernel. Also note that in
defconfig file configs/mvebu_espressobin-88f3720_defconfig is set option
CONFIG_SF_DEFAULT_SPEED=40000000 which is different value than in DT.
Fixes: 0934dddc6436 ("arm: a37xx: Update DTS files to version from upstream Linux kernel") Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Behún [Tue, 22 Mar 2022 16:17:59 +0000 (17:17 +0100)]
arm: mvebu: dts: turris_mox: fix non-working USB port
Commit 0934dddc6436 ("arm: a37xx: Update DTS files to version from
upstream Linux kernel") ported Linux's device-tree files for Armada 3720
SOCs. This broke USB port on Turris MOX, because in Linux' DTS the bus
voltage supply is described as a `phy-supply` property of connector
node, a mechanism that is not supported in U-Boot yet.
For now, fix this by adding `vbus-supply` to usb3 node.
Fixes: 0934dddc6436 ("arm: a37xx: Update DTS files to version from upstream Linux kernel") Signed-off-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
Marek Vasut [Wed, 16 Feb 2022 14:27:59 +0000 (15:27 +0100)]
cmd: eeprom: Do not rewrite EEPROM I2C bus with DM I2C enabled
With DM I2C, the EEPROM bus has been correctly configured in
eeprom_execute_command() already. Do not reconfigure it here
with hard-coded bus number again.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Reviewed-by: Heiko Schocher <hs@denx.de>
This patch replaces use fdtdec_get_addr with simpler dev_read_addr().
fdtdec_get_addr doesn't work properly on ZynqMP-based (64bit) system. Although
not confirmed, it could be related to the fact, that quoting the documentation,
"This variant hard-codes the number of cells used to represent the address and
size based on sizeof(fdt_addr_t) and sizeof(fdt_size_t)".
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com> Reviewed-by: Marek Behún <marek.behun@nic.cz>
Tom Rini [Sun, 20 Mar 2022 19:14:59 +0000 (15:14 -0400)]
Merge tag 'efi-2022-04-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc5
Documentation:
* Fix documentation of FIP creation for Amlogic boards
* Update Nokia RX-51 QEMU documentation
* Add Raspberry Pi documentation
UEFI:
* Fix booting via short form device paths
* Support short form device paths in 'efidebug boot add'
* Fix ESP detection for capsule updates
* Allow ACPI table usage even if device-tree exists - ignore DT
* OP-TEE based GetVariable(): return attributes when buffer too small
The GUID of partitions is sufficient for identification and will stay
constant in the lifetime of a boot option. The preceding path of the
device-path may change due to changes in the enumeration of devices.
Therefore it is preferable to use the short-form of device-paths in load
options. Adjust the 'efidebug boot add' command accordingly.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Alexander Graf [Sun, 27 Feb 2022 12:18:56 +0000 (13:18 +0100)]
efi_loader: Ignore DT when ACPI is on
For targets that enable ACPI, we should not pass Device Trees into
the payload. However, our distro boot logic always passes the builtin
DT as an argument.
To make it easy to use ACPI with distro boot, let's just ignore the DT
argument to bootefi when ACPI is enabled. That way, we can successfully
distro boot payloads on ACPI enabled targets.
Signed-off-by: Alexander Graf <agraf@csgraf.de> Reviewed-by: Mark Kettenis <kettenis@openbsd.org> Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Johan Jonker [Wed, 12 Jan 2022 16:32:11 +0000 (17:32 +0100)]
rockchip: ram: sdram_rk3x88: replace comma by semicolon
A comma at the end of a line gives sometimes strange
effects in combination with some code formatters,
so replace a comma by a semicolon in the sdram_rk3188.c
and sdram_rk3288.c files.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: Set default LNX_KRNL_IMG_TEXT_OFFSET_BASE to SYS_TEXT_BASE
U-Boot can be chainloaded from vendor firmware on ARM64 chromebooks from
a GPT partition (roughly the same as in doc/chromium/chainload.rst), but
an appropriate image header must be built-in to the U-Boot binary by
enabling LINUX_KERNEL_IMAGE_HEADER.
This header has a field for an image load offset from 2MiB alignment
which must also be customized through LNX_KRNL_IMG_TEXT_OFFSET_BASE.
Set it equal to SYS_TEXT_BASE by default for Rockchip boards, which
happens to make this offset zero and works fine on chromebook_kevin
both for chainloading and bare-metal use.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Giulio Benetti [Mon, 14 Mar 2022 09:09:43 +0000 (10:09 +0100)]
rockchip: saradc: remove double semi-colon
Remove double semi-colon that has been forgotten while adding the
driver. This is only a style fix since it doesn't change the
functionality of the driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockchip: rk3328: enable USB mass storage on Renegade
This is very useful to access the LibreComputer eMMC as removable
storage from a PC (e.g. like so `ums 0 mmc 0`). It has been tested as
working on my Renegade board.
Signed-off-by: Leonidas P. Papadakos <papadakospan at gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Johan Jonker [Fri, 24 Dec 2021 17:10:28 +0000 (18:10 +0100)]
MAINTAINERS: add rockchip regex for more files and directories
The current files and directories with wildcard patterns for
Rockchip patches in MAINTAINERS is not always complete.
Add the regex for DT related files and a generic regex for
catching some other forgotten cases, so that the maintainers
receive all Rockchip related patches.
Signed-off-by: Johan Jonker <jbx6244@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Marty E. Plummer [Fri, 24 Dec 2021 13:43:46 +0000 (16:43 +0300)]
rockchip: rk3399: Add support for chromebook_kevin
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com> Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator] Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
This patch enables some configs that should be working on the Bob board,
based on what is observed to work on the Kevin board.
The Bob board uses an Embedded DisplayPort panel compatible with the
simple panel and Rockchip eDP drivers. Its backlight is controlled by
the Chromium OS Embedded Controller Pulse Width Modulator. Enable these
for the board.
Also set VIDEO_ROCKCHIP_MAX_{XRES,YRES} to 1280x800, the resolution of
its panel. This had to be done for the Kevin board, but it's untested if
this is actually necessary for Bob.
The Rockchip video driver needs to assert/deassert some resets, so also
enable the reset controller. RESET_ROCKCHIP defaults to y for this board
when DM_RESET=y, so it's enough to set that.
The Bob board has two USB 3.0 Type-C ports and one USB 2.0 Type-A port
on its right side. Enable the configs relevant to USB devices so these
can be used. This is despite a known issue with RK3399 boards where USB
de-init causes a hang, as there is a known workaround.
Some other rk3399-based devices enable support for the SoC's random
number generator in commit a475bef5340c ("configs: rk3399: enable rng on
firefly/rock960/rockpro64"), as it can provide a KASLR seed when booting
using UEFI. Enable it for Bob as well.
The default misc_init_r() for Rockchip boards sets cpuid and ethernet
MAC address based on e-fuse block. A previous patch extends this on Gru
boards to set registers related to SoC IO domains as is necessary on
these boards. Enable this function and configs for it on Bob.
The microSD card slot on this board (and others based on Gru) is
connected to a GPIO controlled regulator (ppvar-sd-card-io), which must
be operable by U-Boot. Enable the relevant config option to allow this.
Bob boards also use the Winbond W25Q64DW SPI flash chip, enable support
for Winbond SPI flash chips in the board config so U-Boot can boot with
this chip.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
Simon Glass [Fri, 24 Dec 2021 13:43:44 +0000 (16:43 +0300)]
rockchip: gru: Add more devicetree settings
This adds some devicetree settings for the Gru-based boards, based on
what works on a Kevin board.
Gru-based boards usually have an 8MiB SPI flash chip and boot from it.
Make the u-boot.rom file intended to be flashed on it match its size.
Add properties for booting from SPI, and only try to boot from SPI as
MMC and SD card don't seem to work in SPL yet.
The Chromium OS EC needs a delay between transactions so it can get
itself ready. Also it currently uses a non-standard way of specifying
the interrupt. Add these so that the EC works reliably.
The Rockchip Embedded DisplayPort driver is looking for a rockchip,panel
property to find the panel it should work on. Add the property for the
Gru-based boards.
The U-Boot GPIO controlled regulator driver only considers the
"enable-gpios" devicetree property, not the singular "enable-gpio" one.
Some devicetree source files have the singular form as they were added
to Linux kernel when it used that form, and imported to U-Boot as is.
Fix one instance of this in the Gru boards' devicetree to the form that
works in U-Boot.
The PWM controlled regulator driver complains that there is no init
voltage set for a regulator it drives, though it's not clear which one.
Set them all to the voltage levels coreboot sets them: 900 mV.
The RK3399 SoC needs to know the voltage level that some supplies
provides, including one fixed 1.8V audio-related regulator. Although
this synchronization is currently statically done in the board init
functions, a not-so-hypothetical driver that does this dynamically would
query the regulator only to get -ENODATA and be confused. Make sure
U-Boot knows this supply is at 1.8V by setting its limits to that.
Most of this is a reapplication of commit 08c85b57a5ec ("rockchip: gru:
Add extra device-tree settings") whose changes were removed during a
sync with Linux at commit 167efc2c7a46 ("arm64: dts: rk3399: Sync
v5.7-rc1 from Linux"). Apply things to rk3399-gru-u-boot.dtsi instead so
they don't get lost again.
Signed-off-by: Simon Glass <sjg@chromium.org>
[Alper: move to -u-boot.dtsi, rewrite commit message, add more nodes] Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
The RK3399 SoC needs to know the voltage value provided by some
regulators, which is done by setting relevant register bits. Configure
these the way other RK3399 boards do, but with the same values as are
set in the equivalent code in coreboot.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com> Reviewed-by: Kever Yang <kever.yang@rock-chips.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log
