Patrick Delaunay [Wed, 26 Feb 2020 10:26:43 +0000 (11:26 +0100)]
stm32mp1: add 800 MHz profile support
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Wed, 12 Feb 2020 18:37:44 +0000 (19:37 +0100)]
arm: stm32mp: fdt: update kernel device tree according the part number
Update the kernel device tree for STM32MP15x product lines according
the used soc and its part number, when CONFIG_OF_SYSTEM_SETUP is activated:
- STM32MP15XA hasn't Crypto (cryp1/2)
- STM32M151 and STM32M153 hasn't 3D GPU and DSI host
- STM32M151 hasn't CAN FD and has single A7
For example:
FDT: cpu 1 node remove for STM32MP151AAA Rev.B
FDT: can@4400e000 node disabled for STM32MP151AAA Rev.B
FDT: gpu@59000000 node disabled for STM32MP151AAA Rev.B
FDT: dsi@5a000000 node disabled for STM32MP151AAA Rev.B
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Tue, 24 Mar 2020 08:05:00 +0000 (09:05 +0100)]
board: stm32mp1: add finished good in board identifier OTP
Update the command stboard to support the updated coding of OTP 59 with
finished good.
The ST product codification have several element
- "Commercial Product Name" (CPN): type of product board (DKX, EVX)
associated to the board ID "MBxxxx"
- "Finished Good" or "Finish Good" (FG):
effective content of the product without chip STM32MP1 (LCD, Wifi, …)
- BOM: cost variant for same FG
(for example, several provider of the same component)
For example
- commercial product = STM32MP157C-EV1
- Finished Good = EVA32MP157A1$AU1
Booth information are written on board and these information is also saved
in OTP59:
bit [31:16] (hex) => Board id, MBxxxx
bit [15:12] (dec) => Variant CPN (1....15)
bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
bit [7:4] (dec) => Variant FG : finished good (NEW)
bit [3:0] (dec) => BOM (01, .... 255)
The updated command is:
stboard [-y] <Board> <VarCPN> <Revision> <VarFG> <BOM>
And the displayed STMicroelectronics board identification is:
Board: MB<Board> Var<VarCPN>.<VarFG> Rev.<Revision>-<BOM>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Patrick Delaunay [Wed, 12 Feb 2020 18:37:38 +0000 (19:37 +0100)]
arm: stm32mp: bsec: add permanent lock support in bsec driver
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Patrick Delaunay [Wed, 12 Feb 2020 18:37:35 +0000 (19:37 +0100)]
board: stm32mp1: update command stboard on misc_write result
Update management of misc_write, which now return length of data
after the commit 8729b1ae2cbd ("misc: Update read() and write()
methods to return bytes xfered")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com> Acked-by: Patrice Chotard <patrice.chotard@st.com>
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
Tom Rini [Tue, 17 Mar 2020 15:33:59 +0000 (11:33 -0400)]
Merge tag '20200316-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- i2c-gpio: make it possible to run deblock sequence on driver probe
- i2c-gpio: add clock stretching support
- updates the Designware I2C driver for high speed mode,
fix a bug and add some improvements.
- add DM support for memory based bootcounter driver
Tom Rini [Wed, 11 Mar 2020 22:11:18 +0000 (18:11 -0400)]
configs: Drop '$(ARCH)' usage in CONFIG_SPL_LDSCRIPT
In a few boards we had overridden, intentionally, the value used for
CONFIG_SPL_LDSCRIPT. However, rather than using the ARCH value (arm)
they used the $(ARCH) variable in make. This doesn't help really, so
switch to a hard-coded value.
Tom Rini [Wed, 11 Mar 2020 22:11:17 +0000 (18:11 -0400)]
kconfig / kbuild: re-sync with Linux 4.18
Align Kconfig and Kbuild logic to Linux 4.18 release with minimal impact
on files outside of this scope.
Our previous Kconfig sync was done by commit e91610da7c8a ("kconfig:
re-sync with Linux 4.17-rc4").
A very small number of changes upstream since our sync with v4.17-rc4
that exist in the v4.18 release have already been applied here and have
been omitted from the list in this commit (and are readily available in
our own git history).
The imported Linux commits are:
[From prior to v4.17-rc4] 39a33ff80a25 kbuild: remove cc-option-align db547ef19064 Kbuild: don't add obj tree in additional includes b999596b963a Kbuild: don't add ../../ to include path
[From v4.17 to v4.18] b3aa58d2e85d fixdep: suppress consecutive / from file paths in dependency list files 74656b682902 kbuild: disable new dtc graph and unit-address warnings 74d931716151 genksyms: remove symbol prefix support e6ecfb45072c kbuild: do not display CHK for filechk 0b669a5076fd kconfig: refactor Qt package checks for building qconf b464ef583dc7 kconfig: refactor GTK+ package checks for building gconf 1c5af5cf9308 kconfig: refactor ncurses package checks for building mconf and nconf 694c49a7c01c kconfig: drop localization support 96f60dfa5819 trace: Use -mcount-record for dynamic ftrace bb222ceeb327 kconfig: remove string expansion in file_lookup() 96d8e48da55a kconfig: remove string expansion for mainmenu after yyparse() 5b31a9746756 kconfig: remove sym_expand_string_value() 137c0118a900 kconfig: make default prompt of mainmenu less specific e298f3b49def kconfig: add built-in function support 2fd5b09c201e kconfig: add 'shell' built-in function 9de071536c87 kconfig: begin PARAM state only when seeing a command keyword 9ced3bddec08 kconfig: support user-defined function and recursively expanded variable 1175c02506ff kconfig: support simply expanded variable ed2a22f277c6 kconfig: support append assignment operator 82bc8bd82e5c kconfig: expand lefthand side of assignment statement 1d6272e6fe43 kconfig: add 'info', 'warning-if', and 'error-if' built-in functions a702a6176e2f kconfig: add 'filename' and 'lineno' built-in variables 915f64901eb3 kconfig: error out if a recursive variable references itself 2bece88f89fa kconfig: test: add Kconfig macro language tests 21c54b774744 kconfig: show compiler version text in the top comment 59f7b5847b0c kbuild: $(CHECK) doesnt need NOSTDINC_FLAGS twice 145167650b96 kbuild: add endianness flag to CHEKCFLAGS 1f2f01b122d7 kbuild: add machine size to CHECKFLAGS d6a0c8a1326b kconfig: Add testconfig into make help output bb6d83dde191 kbuild: Move last word of nconfig help to the previous line 8593080c0fcf kconfig: fix localmodconfig ed7d40bc67b8 tracing: Fix SKIP_STACK_VALIDATION=1 build due to bad merge with -mrecord-mcount b2d00d7c61c8 kconfig: fix line numbers for if-entries in menu tree ecd53ac2f2c6 kconfig: handle P_SYMBOL in print_symbol() 73d1c580f92b kconfig: loop boundary condition fix 48f6e3cf5bc6 kbuild: do not drop -I without parameter bd412d81b7ea kbuild: .PHONY is not a variable, but PHONY is 6916162c7308 kbuild: remove duplicated comments about PHONY
84e414b0b5bc tests: Add a test case for the omit-if-no-ref keyword 4038fd90056e dtc: add ability to make nodes conditional on them being referenced e1f139ea4900 checks: drop warning for missing PCI bridge bus-range f4eba68d89ee checks: Print duplicate node name instead of parent name 46df1fb1b211 .travis.yml: Run valgrind checks via Travis 14a3002a1aee tests: Update valgrind suppressions for sw_tree1 02c5fe9debc0 tests: Remove valgrind error from tests/get_path df536831d02c checks: add graph binding checks 2347c96edcbe checks: add a check for duplicate unit-addresses of child nodes 8f1b35f88395 Correct overlay syntactic sugar for generating target-path fragments afbddcd418fb Suppress warnings on overlay fragments 119e27300359 Improve tests for dtc overlay generation
[From Linux Kernel commit 50aafd60898a8b3edf2f60e014a8288da3b2e5e3] Signed-off-by: Rob Herring <robh@kernel.org>
[For applying to U-Boot] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Wed, 11 Mar 2020 22:11:15 +0000 (18:11 -0400)]
Azure / GitLab / Travis: Add Kconfig unit tests to a job
The Kconfig language provides a unit test that can be run. As these
require pytest to be installed and run very quickly, bundle them in to
an existing CI job.
Tom Rini [Mon, 24 Feb 2020 18:05:36 +0000 (13:05 -0500)]
mx31pdk: Move CONFIG_SPL_LDSCRIPT to defconfig
As there is only one mx31pdk config file and with upcoming updates to
the Kconfig parsing logic, rather than have an entry in
board/freescale/mx31pdk/Kconfig, move this single setting to the
defconfig file.
Cc: Magnus Lilja <lilja.magnus@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Magnus Lilja <lilja.magnus@gmail.com>
Tom Rini [Wed, 11 Mar 2020 22:11:12 +0000 (18:11 -0400)]
Kconfig: Remove redundant variable sets
In a few places we have Kconfig entries that set SPL_LDSCRIPT to what is
the default value anyways. Drop these.
Cc: Michal Simek <monstr@monstr.eu> Cc: Rick Chen <rick@andestech.com> Cc: Philippe Reynes <tremyfr@yahoo.fr> Cc: Eric Jarrige <eric.jarrige@armadeus.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Michal Simek <michal.simek@xilinx.com> (for Microblaze) Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Tom Rini [Wed, 11 Mar 2020 22:11:11 +0000 (18:11 -0400)]
spl: Kconfig: Escape '$(ARCH)' in LDSCRIPT entries
The default SPL / TPL linker script is in the $(ARCH) directory. The
way we use this today works but isn't ideal. With an update to Kconfig
to re-sync with the Linux Kernel, we need to escape the '$' here so that
it will end up being evaluated by make.
Masahiro Yamada [Tue, 25 Feb 2020 23:02:24 +0000 (08:02 +0900)]
kbuild: remove unused dtc-version.sh script
This is U-Boot own code, and no longer used since commit 36dd5f1b8abc
("dtc: Switch to building and using our own dtc unless provided").
Prior to that commit, U-Boot relied on an external dtc, so this script
was used to check the dtc version.
Now U-Boot bundles our own dtc in script/dtc/dtc like Linux kernel.
Users are still allowed to pass DTC= option from the command line,
but they are supposed to choose correct version of dtc in this case.
So, we do not check the dtc version any more.
Tom Rini [Mon, 24 Feb 2020 17:50:32 +0000 (12:50 -0500)]
kbuild: fixdep: Resync this with v4.17
The previous kbuild resync of e91610da7c8a ("kconfig: re-sync with Linux
4.17-rc4") accidentally did not sync the fixdep program. This commit
brings fixdep in line with the rest of that previous resync.
This includes all of the following Linux kernel commits: fbfa9be9904e kbuild: move include/config/ksym/* to include/ksym/* 5b8ad96d1a44 fixdep: remove some false CONFIG_ matches 14a596a7e6fd fixdep: remove stale references to uml-config.h ab9ce9feed36 fixdep: use existing helper to check modular CONFIG options 87b95a81357d fixdep: refactor parse_dep_file() 5d1ef76f5a22 fixdep: move global variables to local variables of main() ccfe78873c22 fixdep: remove unneeded memcpy() in parse_dep_file() 4003fd80cba9 fixdep: factor out common code for reading files 01b5cbe7012f fixdep: use malloc() and read() to load dep_file to buffer 41f92cffba19 fixdep: remove unnecessary <arpa/inet.h> inclusion 7c2ec43a2154 fixdep: exit with error code in error branches of do_config_file() 4e433fc4d1a9 fixdep: trivial: typo fix and correction dee81e988674 fixdep: faster CONFIG_ search c1a95fda2a40 kbuild: add fine grained build dependencies for exported symbols d8329e35cc08 fixdep: accept extra dependencies on stdin 4c835b57b8de fixdep: constify strrcmp arguments
Of note is that when applying dee81e988674 above our logic in that area
required some careful consideration to continue to apply.
[Fold in bugfix to allow us to include 638e69cf2230 from upstream] Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[Merge everything to U-Boot, rework dee81e988674] Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Tue, 18 Feb 2020 11:05:39 +0000 (20:05 +0900)]
fixdep: fix U-Boot own code to handle only valid symbol characters
Currently, fixdep skips parsing include/linux/kconfig.h, but if it
parsed it, it would translate the following code in kconfig.h
config_enabled(CONFIG_VAL(option##_MODULE)
into:
$(wildcard include/config/option##/module.h)
When Kbuild includes .*.cmd, it would emit the following error:
*** unterminated call to function 'wildcard': missing ')'. Stop.
This issue prevents us from importing the upstream Linux commit 638e69cf2230 ("fixdep: do not ignore kconfig.h").
Fix this by handling only alphanumerical characters and underscores.
This makes sense because they match to the valid character sets in
Kconfig symbols.
As a side-note, you can reproduce this issue only on GNU Make <= 4.2.1
For GNU Make <= 4.2.1, the '#' always means the start of a comment.
Hence, GNU Make thinks the closing ')' is missing.
The following commit in GNU Make changed how it handles '#' in
function invocations. So, this does not happen for GNU Make 4.3
| commit c6966b323811c37acedff05b576b907b06aea5f4
| Author: Paul Smith <psmith@gnu.org>
| Date: Thu Dec 22 18:47:26 2016 -0500
|
| [SV 20513] Un-escaped # are not comments in function invocations
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Reported-by: Tom Rini <trini@konsulko.com>
Suman Anna [Wed, 11 Mar 2020 01:24:29 +0000 (20:24 -0500)]
remoteproc: k3-r5: Fix rproc init failure on Split-mode _only_ devices
The R5F subsystem/cluster on K3 SoCs can support both LockStep and
Split-modes (superset) or just Split-mode depending on an eFUSE
capability register. The LockStep configuration bit is Read-only
though on Split-mode _only_ devices and as such the System Firmware
does not allow the LockStep mode bit to be configured on such devices.
The current logic in k3_r5f_rproc_configure() fails on Split-mode
devices because of this unconditional programming of the LockStep
mode bit, and results in the probe failure shown during the
"rproc init" step at U-Boot prompt.
Fix this by limiting the LockStep mode bit clear configuration only on
devices supporting both LockStep/Split-modes.
Fixes: 4c850356a83f ("remoteproc: Introduce K3 remoteproc driver for R5F subsystem") Signed-off-by: Suman Anna <s-anna@ti.com> Signed-off-by: Andreas Dannenberg <dannenberg@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Suman Anna [Tue, 10 Mar 2020 23:34:54 +0000 (18:34 -0500)]
remoteproc: k3-r5: Fix rproc init failure for Main R5FSS0
The Main R5FSS0 cluster is also enabled to probe the R5F remoteproc
driver within R5 SPL for booting the Core0 very early. This results
in a ti_sci_power_domain_on failure during the probe from the A72
U-Boot when "rproc init" is executed at U-Boot prompt, and doesn't
enumerate all the rproc devices.
Fix this by suppressing the power_domain_on altogether using the
flag DM_FLAG_DEFAULT_PD_CTRL_OFF added in commit af94ad418dc7
("dm: core: Allow for not controlling the power-domain by DM framework").
Suman Anna [Tue, 10 Mar 2020 21:05:56 +0000 (16:05 -0500)]
remoteproc: k3-dsp: Add support for L2RAM loading on C66x DSPs
The resets for the DSP processors on K3 SoCs are managed through the
Power and Sleep Controller (PSC) module. Each DSP typically has two
resets - a global module reset for powering on the device, and a local
reset that affects only the CPU while allowing access to the other
sub-modules within the DSP processor sub-systems.
The C66x DSPs have two levels of internal RAMs that can be used to
boot from, and the firmware loading into these RAMs require the
local reset to be asserted with the device powered on/enabled using
the module reset. Enhance the K3 DSP remoteproc driver to add support
for loading into the internal RAMs. The local reset is deasserted on
SoC power-on-reset, so logic has to be added in probe in remoteproc
mode to balance the remoteproc state-machine.
Note that the local resets are a no-op on C71x cores, and the hardware
does not supporting loading into its internal RAMs.
Suman Anna [Tue, 10 Mar 2020 21:05:55 +0000 (16:05 -0500)]
armv8: K3: j721e: Add DSP internal memory regions in MMU table
The A72 U-Boot code supports early load and boot of a number of
remote processors including the C66_0 and C66_1 DSPs. The current
code supports only loading into the DDR regions which were already
given the appropriate memory attributes. The C66 DSPs also have L1
and L2 internal memory regions that can behave as normal-memories.
Add a new entry to the J721E MMU table covering these regions with
the appropriate memory attributes to allow the A72 U-Boot code to
support loading directly into these memory regions.
Suman Anna [Tue, 10 Mar 2020 21:05:54 +0000 (16:05 -0500)]
remoteproc: k3-dsp: Add a sanity check for DSP boot address alignment
The DSP remote processors on K3 SoCs require a boot register to be
programmed with a boot address, and these boot addresses need to be
aligned on certain address boundaries. The current code does not have
any error checks, and relies on the System Firmware to perform the
checking. Add logic to perform this sanity check within the remoteproc
driver itself to detect these anomalies specifically, and print a
meaningful trace. This avoids the cumbersome debug of root-causing
such failures from the corresponding TI-SCI failure.
The C66x and C71x DSP cores have different alignment needs and are
as follows:
C66x DSP = 1 KB (0x400)
C71x DSP = 2 MB (0x200000)
Suman Anna [Tue, 10 Mar 2020 21:05:53 +0000 (16:05 -0500)]
remoteproc: k3-dsp: Fix unbalanced state machine in k3_dsp_start
The global module reset is deasserted through the ti_sci_power_domain_on()
call in k3_dsp_start(), but is not asserted back if the local module reset
fails. Fix this.
While at this, remove the stale comment about assigned-clock-rates that
seems to have been copied from the K3 ARM64 Remoteproc driver.
Fixes: ab827b385718 ("remoteproc: Introduce K3 C66 and C71 remoteproc driver") Signed-off-by: Suman Anna <s-anna@ti.com>
Heiko Schocher [Mon, 16 Mar 2020 06:55:06 +0000 (07:55 +0100)]
dm: i2c-gpio: add support for clock stretching
This adds support for clock stretching to the i2c-gpio driver. This is
accomplished by switching the GPIO used for the SCL line to an input
when it should be driven high, and polling on the SCL line value until
it goes high (indicating that the I2C slave is no longer pulling it
low).
This is enabled by default; for gpios which cannot be configured as
inputs, the i2c-gpio,scl-output-only property can be used to fall back
to the previous behavior.
Michael Auchter [Fri, 7 Feb 2020 16:55:31 +0000 (10:55 -0600)]
dm: i2c-gpio: rework gpio get/set functions
This patch reworks i2c-gpio to make it easier to switch out the
implementation of the sda/scl get/set functions. This is in preparation
for a patch to conditionally implement clock stretching support.
Marek Vasut [Fri, 7 Feb 2020 15:57:52 +0000 (16:57 +0100)]
i2c: gpio: Run deblock sequence on probe
Add deblock dequence for the I2C bus, needed on some devices. This sequence
is issued once, when probing the driver, and is controlled by DT property,
"i2c-gpio,deblock".
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
Marek Vasut [Fri, 7 Feb 2020 15:57:50 +0000 (16:57 +0100)]
i2c: Export i2c_deblock_gpio_loop()
Export the i2c_deblock_gpio_loop() so it can be used in other places in
U-Boot. In particular, this is useful in the GPIO I2C driver, which claims
the SDA/SCL GPIOs and thus prevents the i2c_deblock() implementation from
claiming the pins as GPIOs again.
Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Heiko Schocher <hs@denx.de>
Tom Rini [Thu, 12 Mar 2020 16:45:27 +0000 (12:45 -0400)]
Merge branch '2020-03-12-rsa-improvements' into next
(Description from AKASHI Takahiro)
extend rsa_verify() for UEFI secure boot:
The current rsa_verify() requires five parameters for a RSA public key
for efficiency while RSA, in theory, requires only two. In addition,
those parameters are expected to come from FIT image.
So this function won't fit very well when we want to use it for the
purpose of implementing UEFI secure boot, in particular, image
authentication as well as variable authentication, where the essential
two parameters are set to be retrieved from one of X509 certificates in
signature database.
So, in this patch, additional three parameters will be calculated on the
fly when rsa_verify() is called without fdt which should contain
parameters above.
This calculation heavily relies on "big-number (or multi-precision)
library." Therefore some routines from BearSSL under MIT license are
imported in this implementation.
AKASHI Takahiro [Fri, 21 Feb 2020 06:12:59 +0000 (15:12 +0900)]
lib: rsa: add rsa_verify_with_pkey()
This function, and hence rsa_verify(), will perform RSA verification
with two essential parameters for a RSA public key in contract of
rsa_verify_with_keynode(), which requires additional three parameters
stored in FIT image.
It will be used in implementing UEFI secure boot, i.e. image authentication
and variable authentication.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Fri, 21 Feb 2020 06:12:58 +0000 (15:12 +0900)]
lib: rsa: generate additional parameters for public key
In the current implementation of FIT_SIGNATURE, five parameters for
a RSA public key are required while only two of them are essential.
(See rsa-mod-exp.h and uImage.FIT/signature.txt)
This is a result of considering relatively limited computer power
and resources on embedded systems, while such a assumption may not
be quite practical for other use cases.
In this patch, added is a function, rsa_gen_key_prop(), which will
generate additional parameters for other uses, in particular
UEFI secure boot, on the fly.
Note: the current code uses some "big number" routines from BearSSL
for the calculation.
AKASHI Takahiro [Fri, 21 Feb 2020 06:12:57 +0000 (15:12 +0900)]
include: image.h: add key info to image_sign_info
For FIT verification, all the properties of a public key come from
"control fdt" pointed to by fdt_blob. In UEFI secure boot, on the other
hand, a public key is located and retrieved from dedicated signature
database stored as UEFI variables.
Added two fields may hold values of a public key if fdt_blob is NULL, and
will be used in rsa_verify_with_pkey() to verify a signature in UEFI
sub-system.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Fri, 21 Feb 2020 06:12:56 +0000 (15:12 +0900)]
rsa: add CONFIG_RSA_VERIFY_WITH_PKEY config
In the next couple of commits, under new CONFIG_RSA_VERIFY_WITH_PKEY,
rsa_verify() will be extended to be able to perform RSA decryption without
additional RSA key properties from FIT image, i.e. rr and n0inv.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
AKASHI Takahiro [Fri, 21 Feb 2020 06:12:55 +0000 (15:12 +0900)]
lib: rsa: decouple rsa from FIT image verification
Introduce new configuration, CONFIG_RSA_VERIFY which will decouple building
RSA functions from FIT verification and allow for adding a RSA-based
signature verification for other file formats, in particular PE file
for UEFI secure boot.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
Eugeniu Rosca [Sun, 8 Mar 2020 00:11:18 +0000 (01:11 +0100)]
image.h: isolate android_image_* functions from tooling
On Feb. 16, 2020, Tom reported [1] build failure of U-Boot in-tree
tooling after applying https://patchwork.ozlabs.org/cover/1229663/
("[v6,0/7] rsa: extend rsa_verify() for UEFI secure boot").
Later on, Heinrich stressed the urgency of the issue in
https://patchwork.ozlabs.org/patch/1250858/#2379069:
>>>>>>>>>
We should finalize the topic as it stops EFI patches from being merged
>>>>>>>>>
On the surface, the problem is caused by U-Boot commits [2-3], which
employed 'u32' in 'include/image.h', while historically U-Boot tooling
stayed agnostic on the {u,s}{8,16,32} types.
Thanks to Tom, Yamada-san and Heinrich, the following solutions have
been put head-to-head ('+' pros, '-' cons):
A. Use an equivalent fixed-size type, i.e. s/u32/uint32_t/ in both
android function prototypes (image.h) and definitions (c file):
+ quick and low-line-count
- creates a 'soup' of fixed-sized types in the Android C file
- will confuse contributors
- is going against Linux kernel best practices [4]
B. Guard Android functions by '!defined(USE_HOSTCC)' in image.h:
+ quick and low-line-count
+ reflects the reality (no android function is used by tooling)
+ zero impact on other subsystems
- ifdeffery may look annoying (pre-existing problem of image.h)
C. Make {u8,u16,u32} available in U-Boot tooling:
+ quick and low-line-count
+ [Yamada-san][5]:
* forbidding u32 for tools is questionable to me
* Linux kernel and Barebox use {u8,u16,u32} for the tools space
- breaks U-Boot tradition?
- has larger impact than [A] and [B]
- adds type complexity/inconsistency in the tooling space
D. [Yamada-san] Refactor the headers to minimize the code shared
between U-Boot space and tooling space:
+ probably the long-term solution
- high effort
- can be seen/done as an incremental update on top of [B]
Looking at the above, [B] looks like the natural way to go forward.
[1] https://patchwork.ozlabs.org/patch/1238245/#2363052
[2] commit 7f2531502c74c0 ("image: android: Add routine to get dtbo params")
[3] commit c3bfad825a71ea ("image: android: Add functions for handling dtb field")
[4] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e6176fa4728fb6d
("checkpatch: add --strict warning for c99 fixed size typedefs : int<size>_t")
[5] https://patchwork.ozlabs.org/patch/1238245/#2363340
Cc: Masahiro Yamada <masahiroy@kernel.org> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Sam Protsenko <joe.skb7@gmail.com> Cc: Lokesh Vutla <lokeshvutla@ti.com> Cc: Simon Glass <sjg@chromium.org> Cc: AKASHI Takahiro <takahiro.akashi@linaro.org> Reported-by: Tom Rini <trini@konsulko.com> Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com> Tested-by: Heinrich Schuchardt <xpyron.glpk@gmx.de>
Sam Shih [Wed, 4 Mar 2020 12:03:48 +0000 (20:03 +0800)]
arm: mediatek: remove unused binman config
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bdd0 ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1eca1 ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com> Tested-by: Frank Wunderlich <frank-w@public-files.de>
Currently when booting the kernel on i.MX8 U-Boot hangs in an
endless loop when switching off dma, connectivity or lsio power
domains during device removal. It hapens first when removing
gpio0 (gpio@5d080000) device, here its power domain device
'lsio_gpio0' is obtained for switching off power. Since the
obtained 'lsio_gpio0' device is removed afterwards, its power
domain is also switched off and here the parent power domain
device 'lsio_power_domain' is optained for switching off the
power. Thereafter, when the obtained 'lsio_power_domain' is
removed, device_remove() removes its first child 'lsio_gpio0'.
During this child removal the 'lsio_power_domain' device is
obtained again for switching and when removing it later,
the same child removal is repeated, so we are stuck in an
endless loop. Below is a snippet from dm tree on i.MX8QXP
for better illustration of the DM devices relationship:
Pedro Jardim [Thu, 13 Feb 2020 12:25:32 +0000 (09:25 -0300)]
mx6slevk: Convert to DM_ETH
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Pedro Jardim [Thu, 13 Feb 2020 17:59:43 +0000 (14:59 -0300)]
mx6sabreauto: Convert to DM_ETH
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
Alifer Moraes [Fri, 14 Feb 2020 19:18:50 +0000 (16:18 -0300)]
arm: dts: imx8mq-evk: add phy-reset-gpios for fec1
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Alifer Moraes [Mon, 10 Feb 2020 14:28:01 +0000 (11:28 -0300)]
mx6sabresd: Convert ethernet to driver model
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Fabien Lehoussel [Mon, 24 Feb 2020 15:45:31 +0000 (16:45 +0100)]
board: sama5d3_xplained: Fix uboot size when loaded from NAND by SPL
Uboot size is incorrect.
Uboot SPL use CONFIG_SYS_MONITOR_LEN to read uboot from NAND : 0x80000
With sama5d3_xplained_nandflash_defconfig : u-boot.bin size is ~800Ko 0xC0000
Clemens Gruber [Mon, 24 Feb 2020 19:52:20 +0000 (20:52 +0100)]
net: phy: marvell: Unify 88E151x series phy_driver
The PHY models of the Marvell 88E151x series are not reliably
distinguishable by their uid / PHY identifiers.
The 88E1510, 88E1512, 88E1514 and 88E1518 all have the same OUI and
model number and bits 3:0 in the PHY Identifier 2 (Page 0, Reg 3) are
described as HW revision number, but both 88E1510 and 88E1518 PHYs were
observed with the same HW rev number (1).
Before commit 83cfbeb0df9f ("net: phy: Fix mask so that we can identify
Marvell 88E1518"), the 88E151x were detected because the HW revision
bits were masked from the uid. After that change, 88E1510/12/18 were all
detected as 88E1518 and the 88E1510 specific code was no longer run.
I modified the mask to again ignore all four HW revision bits, removed
the 88E1510 specific code (board-specific LED/INTn setup), which was not
called since late 2016 anyway and renamed the config function and
phy_driver struct to the better fitting 88e151x.
The uid and mask bits 3:0 are now again the same as in the Linux kernel.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Michal Simek [Tue, 18 Feb 2020 12:51:02 +0000 (13:51 +0100)]
net: phy: dp83867: Add SGMII mode type switching
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Patch description, dt flags have been done in mainline Linux by
commit a2111c460c0c ("net: phy: dp83867: Add documentation for SGMII mode type")
and by commit 507ddd5c0d47 ("net: phy: dp83867: Add SGMII mode type switching")
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Michal Simek [Mon, 17 Feb 2020 09:38:57 +0000 (10:38 +0100)]
dt-bindings: net: dp83867: Remove binding doc from U-Boot tree
U-Boot is having DT which doesn't cover all options currently supported by
driver. DT binding is aligned with Linux kernel version available here.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ti,dp83867.txt
Based on my talk with Grygorii Strashko better will be to remove it.
Also Linux kernel bindings are being converted to yaml that's another
reason to do it only at one place.
Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Alex Marginean [Thu, 9 Jan 2020 08:50:05 +0000 (10:50 +0200)]
net: phy: add XFI, USXGMII types to is_10g_interface() helper
The helper is used to reset PHYs on connect and it determines the clause
to use (C22/C45) based on interface type. This fixes 'PHY reset timed out'
warnings in console for USXGMII/XFI PHYs.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Fri, 3 Jan 2020 22:08:47 +0000 (22:08 +0000)]
net: phy: Fix overlong PHY timeout
Commit 27c3f70f3b50 ("net: phy: Increase link up delay in
genphy_update_link()") increased the per-iteration waiting time from
1ms to 50ms, without adjusting the timeout counter. This lead to the
timeout increasing from the typical 4 seconds to over three minutes.
Adjust the timeout counter evaluation by that factor of 50 to bring the
timeout back to the intended value.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Fixes: net: phy: Increase link up delay in genphy_update_link() ("27c3f70f3b50") Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Matthias Brugger <mbrugger@suse.com> Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Andre Przywara [Mon, 25 Nov 2019 01:32:15 +0000 (01:32 +0000)]
doc: net: Rewrite network driver documentation
doc/README.drivers.eth seems like a good source for understanding
U-Boot's network subsystem, but is only talking about legacy network
drivers. This is particularly sad as proper documentation would help in
porting drivers over to the driver model.
Rewrite the document to describe network drivers in the new driver model
world. Most driver callbacks/methods are almost identical in their
semantic, but recv() differs in some important details.
Also keep some parts of the original text at the end, to help
understanding old drivers. Add some hints on how to port drivers over.
This also uses the opportunity to reformat the document in reST, on the
way moving it into doc/driver-model and adding it into the structure
there.
Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Alex Marginean [Wed, 4 Dec 2019 13:32:15 +0000 (15:32 +0200)]
drivers: net: phy: aquantia: drop XGMII as a valid system interface proto
Use either USXGMII or XFI in aquantia_set_proto and drop XGMII as a valid
protocol configuration. The PHY doesn't support it, it's just used as an
alias for one of the other two protocols.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com> Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add NC-SI to the usual phy handling. This makes two notable changes:
- Somewhat similar to a fixed phy, phy_connect() will create an NC-SI
phy if CONFIG_PHY_NCSI is defined.
- An early return is added to phy_read() and phy_write() to handle a
case like the NC-SI phy which does not define a bus.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This introduces support for the NC-SI protocol, modelled as a phy driver
for other ethernet drivers to consume.
NC-SI (Network Controller Sideband Interface) is a protocol to manage a
sideband connection to a proper network interface, for example a BMC
(Baseboard Management Controller) sharing the NIC of the host system.
Probing and configuration occurs by communicating with the "remote" NIC
via NC-SI control frames (Ethernet header 0x88f8).
This implementation is roughly based on the upstream Linux
implementation[0], with a reduced feature set and an emphasis on getting
a link up as fast as possible rather than probing the full possible
topology of the bus.
The current phy model relies on the network being "up", sending NC-SI
command frames via net_send_packet() and receiving them from the
net_loop() loop (added in a following patch).
The ncsi-pkt.h header[1] is copied from the Linux kernel for consistent
field definitions.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tom Rini [Mon, 9 Mar 2020 17:01:57 +0000 (13:01 -0400)]
Azure/Travis: Re-sync jobs and clarify exclusions
We keep both of these jobs in sync as much as possible even when the
primary motivation is to keep Travis from exceeding the build time limit
there. With that in mind:
- Use "rk" not "rockchip" to get all Rockchip SoC platforms in one job,
rather than just all Rockchip vendor platforms.
- The NXP LX216* SoCs have their own job, exclude them from the AArch64
generic job.
- SoCFPGA SoCs have their own job, exclude them from the AArch64 generic
job.
Giulio Benetti [Fri, 31 Jan 2020 13:39:47 +0000 (14:39 +0100)]
serial_lpuart: make clock failure less verbose
Some device may enable CONFIG_CLK but not still support this clock in
CC, so better use debug() in place of dev_warn() otherwise a lot of
boards will throw useless dev_warn()s.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com> Reviewed-by: Simon Glass <sjg@chromium.org>
imx8mm/mn: Add missing root clock entry for ARM core clock
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM
code to retrieve the core clock frequency. As the root clock is not
listed we currently get:
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Fix this by adding the missing entry, which results in:
Baruch Siach [Tue, 4 Feb 2020 16:57:08 +0000 (18:57 +0200)]
mx6cuboxi: don't disable fdt relocation
fdt_high value of 0xffffffff disables fdt relocation on boot. We don't
need that for Cubox-i/Hummingboard. Rely on generic code to find the
optimal fdt location at boot time.
projects / u-boot.git / log
