Gero Schumacher [Tue, 26 Feb 2019 15:45:22 +0000 (15:45 +0000)]
fs: ext4: Problem with ext4load and sparse files
Hi,
when I try to load a sparse file via ext4load, I am getting the error message
'invalid extent'
After a deeper look in the code, it seems to be an issue in the function ext4fs_get_extent_block in fs/ext4/ext4_common.c:
The file starts with 1k of zeros. The blocksize is 1024. So the first extend block contains the following information:
eh_entries: 1
eh_depth: 1
ei_block 1
When the upper layer (ext4fs_read_file) asks for fileblock 0, we are running in the 'invalid extent' error message.
For me it seems, that the code is not prepared for handling a sparse block at the beginning of the file. The following change, solved my problem:
I am really not an expert in ext4 filesystems. Can somebody please have a look at this issue and give me a feedback, if I am totally wrong or not?
Test cases are:
1) basic link creation, verify it can be followed
2) chained links, verify it can be followed
3) replace exiting file a with a link, and a link with a link. verify it
can be followed
4) create a broken link, verify it can't be followed
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
fs: ext4: Add support for the creation of symbolic links
Re-use the functions used to write/create a file, to support creation of a
symbolic link.
The difference with a regular file are small:
- The inode mode is flagged with S_IFLNK instead of S_IFREG
- The ext2_dirent's filetype is FILETYPE_SYMLINK instead of FILETYPE_REG
- Instead of storing the content of a file in allocated blocks, the path
to the target is stored. And if the target's path is short enough, no block
is allocated and the target's path is stored in ext2_inode.b.symlink
As with regulars files, if a file/symlink with the same name exits, it is
unlinked first and then re-created.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix ext4 env code] Signed-off-by: Tom Rini <trini@konsulko.com>
fs: ext4: constify the buffer passed to write functions
There is no need to modify the buffer passed to ext4fs_write_file().
The memset() call is not required here and was likely copied from the
equivalent part of the ext4fs_read_file() function where we do need it.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
We need to make sure that file writes,file creation, etc. are properly
performed and do not corrupt the filesystem.
To help with this, introduce the assert_fs_integrity() function that
executes the appropriate fsck tool. It should be called at the end of any
test that modify the content/organization of the filesystem.
Currently only supports FATs and EXT4.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Wed, 30 Jan 2019 19:58:05 +0000 (12:58 -0700)]
fs: ext4: cache extent data
When a file contains extents, U-Boot currently reads extent-related data
for each block in the file, even if that data is located in the same
block each time. This significantly slows down loading of files that use
extents. Implement a very dumb cache to prevent repeatedly reading the
same block. Files with extents now load as fast as files without.
Note: There are many cases where read_allocated_block() is called. This
patch only addresses one of those places; all others still read redundant
data in any case they did before. This is a minimal patch to fix the
load command; other cases aren't fixed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Stefan Roese [Wed, 27 Mar 2019 10:20:19 +0000 (11:20 +0100)]
net: macb: Add small delay after link establishment
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.
Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Wenyou Yang <wenyou.yang@atmel.com> Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Claudiu Beznea [Mon, 25 Mar 2019 10:33:56 +0000 (10:33 +0000)]
pinctrl: at91: add option to use drive strength bits
SAM9X60 uses high and low drive strengths. To implement this, in
at91_pinctrl_mux_ops::set_drivestrength we need bit numbers of
drive strengths (1 for low, 2 for high), thus change the code to
allow the usage of drive strength bit numbers.
Stefan Roese [Tue, 2 Apr 2019 08:57:27 +0000 (10:57 +0200)]
arm: at91: Add gardena-gateway-at91sam support
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Tue, 2 Apr 2019 08:57:25 +0000 (10:57 +0200)]
arm: at91: siemens: Add support to generate combined SPL+U-Boot image
This patch adds the necessary defines to the Siemens AT91SAM based
boards (smartweb, corvus and taurus) to generate the combined binary
image with SPL and main U-Boot image combined (u-boot-with-spl.bin).
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Wed, 3 Apr 2019 13:24:50 +0000 (15:24 +0200)]
Makefile: Add Kconfig option CONFIG_SPL_IMAGE to select the SPL binary
This patch adds the CONFIG_SPL_IMAGE option to select the SPL image that
shall be used to generate the combined SPL + U-Boot image. The default
value is the current value "spl/u-boot-spl.bin".
This patch also sets CONFIG_SPL_IMAGE to "spl/boot.bin" for AT91 targets
which use SPL NAND support (boot from NAND). For these build targets the
combined image "u-boot-with-spl.bin" is now automatically generated and
can be programmed into NAND as one single image (vs. SPL image and U-Boot
as 2 separate images).
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
Stefan Roese [Tue, 2 Apr 2019 08:57:23 +0000 (10:57 +0200)]
Makefile.spl: Move generated AT91SAM NAND image boot.bin to spl directory
This patch moves the AT91SAM NAND booting SPL image "boot.bin" which
includes the ECC values from the root directory into the spl directory,
where all SPL related images are located.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Tue, 2 Apr 2019 08:57:22 +0000 (10:57 +0200)]
arm: at91: arm926ejs/u-boot-spl.lds: Add _image_binary_end to SPL lds
This patch adds _image_binary_end to the SPL linker script. This will be
used be the upcoming GARDENA AT91SAM based platform, which uses DT in
SPL and configures CONFIGURE_SPL_SEPARATE_BSS.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Wed, 3 Apr 2019 05:37:40 +0000 (07:37 +0200)]
arm: at91: Enable watchdog support
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
Stefan Roese [Wed, 3 Apr 2019 05:37:05 +0000 (07:37 +0200)]
arm: at91: Remove CONFIG_AT91_HW_WDT_TIMEOUT
This patch removes the CONFIG_AT91_HW_WDT_TIMEOUT as its not needed any
more. The WD timeout value can be provided via the "timeout-sec" DT
property. If not provided this way, the default value of 2 seconds will
be used.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
Stefan Roese [Tue, 2 Apr 2019 08:57:19 +0000 (10:57 +0200)]
watchdog: at91sam9_wdt: Fix WDT setup in at91_wdt_start()
This patch fixes the timer register setup in at91_wdt_start() to
correctly configure the register again. The input timeout value is
now in milli-seconds instead of seconds with the new watchdog API.
Make sure to take this into account and only use a max timeout
value of 16 seconds as appropriate for this SoC.
Also the check against a lower timeout value than 0 is removed. This
check makes no sense, as the timeout value is unsigned.
Signed-off-by: Stefan Roese <sr@denx.de> Reported-by: Heiko Schocher <hs@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Tue, 2 Apr 2019 08:57:18 +0000 (10:57 +0200)]
watchdog: Handle SPL build with watchdog disabled
This patch adds some checks, so that the watchdog can be enabled in main
U-Boot proper but can be disabled in SPL.
This will be used by some AT91SAM based boards, which might enable the
watchdog in the main U-Boot proper and not in SPL. It will be enabled in
SPL by default there, so no need to configure it there. This approach
saves some space in SPL.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
Stefan Roese [Wed, 3 Apr 2019 13:24:19 +0000 (15:24 +0200)]
serial: atmel_usart: Use fixed clock value in SPL version with DM_SERIAL
This patch adds an alterative SPL version of atmel_serial_enable_clk().
This enables the usage of this driver without full clock support (in
drivers and DT nodes). This saves some space in the SPL image.
Please note that this fixed clock support is only added to the SPL code
in the DM_SERIAL part of this file. All boards not using SPL & DM_SERIAL
should not be affected.
This patch also introduces CONFIG_SPL_UART_CLOCK for the fixed UART
input clock. It defaults to 132096000 for ARCH_AT91 but can be set to
a different value if needed.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com>
Stefan Roese [Tue, 2 Apr 2019 08:57:16 +0000 (10:57 +0200)]
arm: at91: spl_at91.c: Call spl_early_init() if OF_CONTROL is enabled
This patch adds a call to spl_early_init() to board_init_f() which is
needed when CONFIG_SPL_OF_CONTROL is configured. This is necessary for
the early SPL setup including the DTB setup for later usage.
Please note that this call might also be needed for non SPL_OF_CONTROL
board, like the smartweb target. But smartweb fails to build with this
call because its binary grows too big. So I disabled it for these kind
of targets for now.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Andreas Bießmann <andreas@biessmann.org> Cc: Eugen Hristev <eugen.hristev@microchip.com> Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board: Tested-by: Heiko Schocher <hs@denx.de>
Alexander Dahl [Fri, 22 Mar 2019 13:25:54 +0000 (14:25 +0100)]
ARM: at91: sama5d2: Wrap cpu detection to fix macb driver
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional
chip id. The check if the cpu is sama5d2 was changed from a preprocessor
definition (inlining a call to 'get_chip_id()') to a C function,
probably to not call get_chip_id twice?
That however broke a check in the macb ethernet driver. That driver is
more generic and also used for other platforms. I suppose this solution
was implemented to use it in 'gem_is_gigabit_capable()', without having
to stricly depend on the at91 platform:
That only works as long as cpu_is_sama5d2 is a preprocessor definition.
(The same is still true for sama5d4 by the way.) So this is a straight
forward fix for the workaround.
The not working check on the SAMA5D2 CPU lead to an issue on a custom
board with a LAN8720A ethernet phy connected to the SoC:
Jagan Teki [Mon, 8 Apr 2019 20:27:54 +0000 (01:57 +0530)]
arm: sunxi: Enable DM_MMC on required SoCs
Enabling DM_MMC is forcing CONFIG_BLK=y so if any board which uses
SCSI must need to enable DM_SCSI otherwise SCSI reads on that particular
target making invalid reading to the disk drive.
Allwinner platform do support SCSI on A10, A20 and R40 SoC's out of
these only A10 have DM_SCSI enabled. So enabling DM_MMC on A20, R40
would eventually end-up with scsi disk read failures like [1]
So, enable DM_MMC in all places of respective SoC's instead of enabling
them globally to Allwinner platform.
Now, DM_MMC is enabled in Allwinner SoC's except A20 and R40.
net: dm: fec: Support phy-reset-post-delay property
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com> Reviewed-by: Anatolij Gustschin <agust@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Lukasz Majewski <lukma@denx.de>
Stefan Roese [Wed, 3 Apr 2019 07:12:48 +0000 (09:12 +0200)]
watchdog: Move watchdog_dev to data section (BSS may not be cleared)
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Tom Rini <trini@konsulko.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: "Marek Behún" <marek.behun@nic.cz> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100) Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Rick Chen [Tue, 2 Apr 2019 07:56:39 +0000 (15:56 +0800)]
riscv: Add a SYSCON driver for Andestech's PLIC
The Platform-Level Interrupt Controller (PLIC)
block holds memory-mapped claim and pending registers
associated with software interrupt. It is required
for handling IPI.
Signed-off-by: Rick Chen <rick@andestech.com> Cc: Greentime Hu <greentime@andestech.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Lukas Auer [Sun, 17 Mar 2019 18:28:39 +0000 (19:28 +0100)]
riscv: do not rely on hart ID passed by previous boot stage
RISC-V U-Boot expects the hart ID to be passed to it via register a0 by
the previous boot stage. Machine mode firmware such as BBL and OpenSBI
do this when starting their payload (U-Boot) in supervisor mode. If
U-Boot is running in machine mode, this task must be handled by the boot
ROM. Explicitly populate register a0 with the hart ID from the mhartid
CSR to avoid possible problems on RISC-V processors with a boot ROM that
does not handle this task.
Suggested-by: Rick Chen <rick@andestech.com> Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Atish Patra <atish.patra@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Tested-by: Rick Chen <rick@andestech.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:37 +0000 (19:28 +0100)]
riscv: add support for multi-hart systems
On RISC-V, all harts boot independently. To be able to run on a
multi-hart system, U-Boot must be extended with the functionality to
manage all harts in the system. All harts entering U-Boot are registered
in the available_harts mask stored in global data. A hart lottery system
as used in the Linux kernel selects the hart U-Boot runs on. All other
harts are halted. U-Boot can delegate functions to them using
smp_call_function().
Every hart has a valid pointer to the global data structure and a 8KiB
stack by default. The stack size is set with CONFIG_STACK_SIZE_SHIFT.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:36 +0000 (19:28 +0100)]
riscv: save hart ID in register tp instead of s0
The hart ID passed by the previous boot stage is currently stored in
register s0. If we divert the control flow inside a function, which is
required as part of multi-hart support, the function epilog may not be
called, clobbering register s0. Save the hart ID in the unallocatable
register tp instead to protect the hart ID.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Rick Chen <rick@andestech.com> Reviewed-by: Anup Patel <anup.patel@wdc.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:35 +0000 (19:28 +0100)]
riscv: delay initialization of caches and debug UART
Move the initialization of the caches and the debug UART until after
board_init_f_init_reserve. This is in preparation for SMP support, where
code prior to this point will be executed by all harts. This ensures
that initialization will only be performed once on the main hart running
U-Boot.
Lukas Auer [Sun, 17 Mar 2019 18:28:34 +0000 (19:28 +0100)]
riscv: implement IPI platform functions using SBI
The supervisor binary interface (SBI) provides the necessary functions
to implement the platform IPI functions riscv_send_ipi() and
riscv_clear_ipi(). Use it to implement them.
This adds support for inter-processor interrupts (IPIs) on RISC-V CPUs
running in supervisor mode. Support for machine mode is already
available for CPUs that include the SiFive CLINT.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Atish Patra <atish.patra@wdc.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Lukas Auer [Sun, 17 Mar 2019 18:28:33 +0000 (19:28 +0100)]
riscv: import the supervisor binary interface header file
Import the supervisor binary interface (SBI) header file from Linux
(arch/riscv/include/asm/sbi.h). The last change to it was in commit 6d60b6ee0c97 ("RISC-V: Device, timer, IRQs, and the SBI").
Lukas Auer [Sun, 17 Mar 2019 18:28:32 +0000 (19:28 +0100)]
riscv: add infrastructure for calling functions on other harts
Harts on RISC-V boot independently, U-Boot is responsible for managing
them. Functions are called on other harts with smp_call_function(),
which sends inter-processor interrupts (IPIs) to all other available
harts. Available harts are those marked as available in the device tree
and present in the available_harts mask stored in global data. The
available_harts mask is used to register all harts that have entered
U-Boot. Functions are specified with their address and two function
arguments (argument 2 and 3). The first function argument is always the
hart ID of the hart calling the function. On the other harts, the IPI
interrupt handler handle_ipi() must be called on software interrupts to
handle the request and call the specified function.
Functions are stored in the ipi_data data structure. Every hart has its
own data structure in global data. While this is not required at the
moment (all harts are expected to boot Linux), this does allow future
expansion, where other harts may be used for monitoring or other tasks.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de> Reviewed-by: Anup Patel <anup.patel@wdc.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Bin Meng <bmeng.cn@gmail.com>
Hannes Schmelzer [Fri, 29 Mar 2019 08:54:05 +0000 (09:54 +0100)]
net: phy: implement fallback mechanism for negative phy adresses
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com> Tested-by: Michal Simek <michal.simek@xilinx.com> Tested-by: Lukasz Majewski <lukma@denx.de>
In the extended text input protocol CTRL-A - CTRL-Z have to be signaled as
Unicode characters a-z or A-Z depending on the shift state and not as 0x01
to 0x1a.
Update Python unit test.
This patch is required for using the EFI shell `edit` command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
EFI shell command edit uses the SetInfo() methods to unset the read only
attribute of the file to be edited. So let efi_file_setinfo() return
success in this case.
Return an error if the function is called for to rename or resize a file
as we do not support this yet.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The EFI shell expects that after opening a file with EFI_FILE_MODE_CREATE
GetInfo() succeeds. Up to now we do not actually create the file when
method Open() of the EFI_FILE_PROTOCOL is called.
If method Open() of the EFI_FILE_PROTOCOL is called with
EFI_FILE_MODE_CREATE and the file does not yet exist, call fs_write() with
a buffer size of zero to actually create the file.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: debug output file handle in efi_file_open()
For debugging it is helpful to know the address of the file handle created
by the Open() method of the EFI file protocol. So let's write it with
EFI_PRINT().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: variables PlatformLang and PlatformLangCodes
Since TianoCore EDK2 commit d65f2cea36d1 ("ShellPkg/CommandLib: Locate
proper UnicodeCollation instance") in edk2 the UEFI Shell crashes if EFI
variable PlatformLang is not defined.
As this variable is anyway prescribed in the UEFI 2.7 spec let's define it
to L"en-US". Use the same value for PlatformLangCodes that defines the list
of all supported languages.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: parameter checks in StartImage and Exit()
Add parameter checks in the StartImage() and Exit() boottime services:
- check that the image handle is valid and has the loaded image protocol
installed
- in StartImage() record the current image
- in Exit() check that the image is the current image
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
AKASHI Takahiro [Thu, 11 Oct 2018 11:09:58 +0000 (04:09 -0700)]
efi_loader: set image_base and image_size to correct values
Currently, image's image_base points to an address where the image was
temporarily uploaded for further loading. Since efi_loader relocates
the image to final destination, image_base and image_size should reflect
that.
This bug was detected in UEFI SCT, "Loaded Image Protocol Test - test 2,"
which shows that 'Unload' function doesn't fit into a range suggested by
image_base and image_size.
Changes in this patch also includes:
* reverts a patch, "efi_loader: save image relocation address
and size" since newly added fields are no longer needed.
* copy PE headers as well since those information will be needed
for module loading, in particular, at gurb.
(This bug was reported by Heinrich.)
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Rebase patch.
Remove unused fields from struct efi_loaded_image_obj.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
efi_loader: release file buffer after loading image
Commit 0e18f584de59 ("efi_loader: LoadImage: always allocate new pages")
ensured that whether we load an image from file or from memory we end up
with the same number of newly allocated buffers. But essentially we ended
up with one buffer too many in both cases:
efi_load_pe() copies and rebases the UEFI image.
We do not need the buffer with the file contents afterwards.
Fixes: 0e18f584de59 ("efi_loader: LoadImage: always allocate new pages") Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Thomas Petazzoni [Sat, 30 Mar 2019 14:29:23 +0000 (15:29 +0100)]
tools/Makefile: build host tools with -std=gnu99
Parts of the code are using C99 constructs (such as variables declared
inside loops), but also GNU extensions (such as typeof), so using
-std=gnu99 is necessary to build with older versions of gcc that don't
default to building with gnu99.
It fixes the following build failure:
./tools/../lib/crc16.c: In function "crc16_ccitt":
./tools/../lib/crc16.c:70:2: error: "for" loop initial declarations are only allowed in C99 mode
for (int i = 0; i < len; i++)
^
./tools/../lib/crc16.c:70:2: note: use option -std=c99 or -std=gnu99 to compile your code
when building the host tools with gcc 4.7.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Neil Armstrong [Wed, 3 Apr 2019 11:46:37 +0000 (13:46 +0200)]
configs: khadas_vim2: Fix defconfig
The Khadas VIM2 defconfig was missing the USB PHY config and
two other misc configs to setup dram banks and call misc_init_r.
Align it on the other Amlogic SoC based boards defconfig.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The FEC ETH driver switched to PHY GPIO reset performed with data defined
in DTS.
For the HSC|DDC boards the GPIO reset signal is active low and hence the
wrong DTS description must be changed (otherwise the reset for ETH is not
properly setup).
Jagan Teki [Thu, 28 Mar 2019 08:16:11 +0000 (13:46 +0530)]
clk: sunxi: a10: Add CLK_AHB_GMAC
CLK_AHB_GMAC was suppose to be part of previous commit
"clk: sunxi: Implement A10 EMAC clocks" add it so-that
we can get rid of sunxi_set_gate warning on boot message.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fabio Estevam [Wed, 27 Mar 2019 23:03:39 +0000 (20:03 -0300)]
pico-imx7d: README: Recommend the usage of a USB hub
Since commit 9e3c0174da842 ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Jagan Teki [Thu, 21 Mar 2019 08:35:53 +0000 (14:05 +0530)]
configs: icorem6: Use imx6 cratch register for bootcount
SRAM address used for bootcount on exiting code is erasing
previous count value when system reset from Linux. So use
the dedicated imx6 scratch register, GPR2 to preserve the
contents even if the system reset from Linux.
Fixes: 4eb9aa39350e ("configs: imx6qdl_icore_mmc: Enable watchdog and bootcounter") Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com> Signed-off-by: Jagan Teki <jagan@amarulasolutions.com> Tested-by: Shyam Saini <shyam.saini@amarulasolutions.com> Reviewed-by: Stefano Babic <sbabic@denx.de>
Adam Ford [Sun, 3 Mar 2019 22:22:45 +0000 (16:22 -0600)]
ARM: imx6q_logic: Enable UUID support
With UUID support, the root can now point to UUID. This makes
swiching between mmc 0 and mmc 1 easier by simplying changing
mmcdev between 0 and 1. From there, the scripts handle the rest.
Fabio Estevam [Thu, 21 Mar 2019 13:59:06 +0000 (10:59 -0300)]
pico-imx6ul: Fix eMMC boot after DM_MMC conversion
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br> Signed-off-by: Fabio Estevam <festevam@gmail.com> Tested-by: Fabio Berton <fabio.berton@ossystems.com.br> Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
projects / u-boot.git / log
![5 years agoefi_loader: boottime: export efi_[un]load_image()](/%22/img/sics.gif/%22/static/git-favicon.png?p=u-boot.git;a=commit;h=d7e0b0109ebed35c7b91545417e6f7a28cb540d9){kind=link}
