Heiko Schocher [Wed, 7 Jun 2017 15:33:11 +0000 (17:33 +0200)]
powerpc, 5xx: remove support for 5xx
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Heiko Schocher [Wed, 7 Jun 2017 15:33:10 +0000 (17:33 +0200)]
powerpc, 8260: remove support for mpc8260
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Heiko Schocher [Wed, 7 Jun 2017 15:33:09 +0000 (17:33 +0200)]
powerpc, 8xx: remove support for 8xx
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Semen Protsenko [Mon, 22 May 2017 16:16:40 +0000 (19:16 +0300)]
omap: Add routine for setting fastboot variables
This patch reuses new option, which allows us to expose variables
from environment to "fastboot getvar" command. Those variables must be
of "fastboot.%s" format.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Manfred Schlaegl [Wed, 10 May 2017 13:41:32 +0000 (15:41 +0200)]
ARM: fixed relocation using proper alignment
Using u-boot-2017.05 on i.MX6UL we ran into following problem:
Initially U-Boot could be started normally.
If we added one random command in configuration, the newly generated
image hung at startup (last output was DRAM: 256 MiB).
We tracked this down to a data abort within relocation (relocated_code).
relocated_code in arch/arm/lib/relocate.S copies 8 bytes per loop
iteration until the source pointer is equal to __image_copy_end.
In a good case __image_copy_end was aligned to 8 bytes, so the loop
stopped as suggested, but in an errornous case __image_copy_end was
not aligned to 8 bytes, so the loop ran out of bounds and caused a
data abort exception.
This patches solves the issue by aligning __image_copy_end to 8 byte
using the linker script related to arm.
I don't know if it's the correct way to solve this, so some review would
be very appreciated.
Tom Rini [Sat, 10 Jun 2017 14:01:05 +0000 (10:01 -0400)]
dm: blk: Fix warning on !CONFIG_BLK
When we don't have CONFIG_BLK defined we don't have a forward
declaration of struct udevice, and thus get a warning about it on
blk_get_from_parent(), which we only have when CONFIG_BLK is set. Move
the declaration of blk_get_from_parent() to be with the other CONFIG_BLK
parts.
Fixes 9f103b9cb5f8 ("dm: blk: Add a way to obtain a block device from ...") Signed-off-by: Tom Rini <trini@konsulko.com>
igep0020: Enable DISTRO_DEFAULTS on IGEPv2 platforms
Like commit 3337e3af5d3d this enables suitable commands needed for booting
general purpose Linux distribution. This is required for example if we want
to use PXE or DHCP as default boot targets, symbols no longer enabled by
config_distro_defaults.h.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Lokesh Vutla [Mon, 5 Jun 2017 09:18:17 +0000 (14:48 +0530)]
board: ti: am572x-evm: Update pinmux using latest PMT
Update the board pinmux for AM572x-evm using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 and am572x_gp_evm_A2b_sr1p1
that were autogenerated on 30th January, 2017 by
"Ahmad Rashed <a-rashed@ti.com>" and "Tom Johnson <thjohnson@ti.com>".
Lokesh Vutla [Mon, 5 Jun 2017 09:18:16 +0000 (14:48 +0530)]
board: ti: am571x-idk: Update pinmux using latest PMT
Update the board pinmux for AM571x-IDK board using latest PMT[1] and the
board files named am571x_idk_v1p3b_sr2p0 that were autogenerated on
23rd March, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
Lokesh Vutla [Mon, 5 Jun 2017 09:18:15 +0000 (14:48 +0530)]
board: ti: am572x-idk: Update pinmux using latest PMT
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
30th January, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
armv7m: Disable D-cache when booting nommu(ARMv7M) Linux kernel
Disable D-Cache is required when booting nommu Linux kernel.
(please see Linux kernel source "arch/arm/kernel/head-nommu.S")
U-Boot is enabled D-cache and I-Cache at startup.
However, it does not disable D-Cache before
booting nommu Linux kernel.
Therefore, I call dcache_disable()
when the CPU is ARMv7M to fix this problem.
Semen Protsenko [Fri, 2 Jun 2017 15:00:00 +0000 (18:00 +0300)]
arm: omap: Unify get_device_type() function
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.
Details:
- Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
OMAP4/5), so we can obtain status register in common way
- For now ctrl structure for AM33xx/OMAP3 contains only status register
address
- Run hw_data_init() in order to assign ctrl to proper structure
- Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
(DEVICE_TYPE_MASK and GP_DEVICE are used instead)
- Guard structs in omap_common.h with #ifdefs, because otherwise
including omap_common.h on non-omap4/5 board files breaks compilation
Buildman script was run for all OMAP boards. Result output:
arm: (for 38/616 boards)
all +352.5
bss -1.4
data +3.5
rodata +300.0
spl/u-boot-spl:all +284.7
spl/u-boot-spl:data +2.2
spl/u-boot-spl:rodata +252.0
spl/u-boot-spl:text +30.5
text +50.4
(no errors to report)
Tested on AM57x EVM and BeagleBoard xM.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx] Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 9 Jun 2017 20:59:17 +0000 (16:59 -0400)]
am33xx: Finish migration of CONFIG_AM33XX/AM43XX
Almost all users of CONFIG_AM33XX/AM43XX have been migrated. Finish
moving the last few over to Kconfig, and put all of the boards under the
appropriate Kconfig chocie now. This board choice is non-optional, so
remove that keyword on am33xx.
buildman: properly translate strings for log and err files to ASCII
The build output can still produce unicode encoded output. But in
the buildman's log and err files we only want plain ASCII characters.
To handle all situations with unicode and non-unicode output, encode
the stdout and stderr strings to UTF-8 and afterwards to ASCII with
replacing all special characters.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
buildman: disable localized and unicode output of all build tools
Build tools like Make, gcc or binutils support localized output
or unicode encoded output dependent on the default system locale.
This is not useful for buildman, where we want reproducible
warning or error messages or where the output of binutils is
further processed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Simon Glass [Wed, 31 May 2017 23:57:33 +0000 (17:57 -0600)]
rockchip: rk3288: Allow setting up clocks in U-Boot proper
If U-Boot is chain-loaded from a previous boot loader we must set up the
clocks the way U-Boot wants them. Add code for this. It will do nothing if
SPL has already done the job.
Simon Glass [Wed, 31 May 2017 23:57:31 +0000 (17:57 -0600)]
rockchip: rk3288: Convert clock driver to use shifted masks
Shifted masks are the standard approach with rockchip since it allows
use of the mask without shifting it each time. Update the definitions and
the driver to match.
Simon Glass [Wed, 31 May 2017 23:57:29 +0000 (17:57 -0600)]
rockchip: video: Take the vop device out of standby
On reset the standby bit is clear, but if U-Boot is chain-loaded from
another boot loader it may be set. Clear it before starting up video so
that it works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby': Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Wed, 31 May 2017 23:57:28 +0000 (17:57 -0600)]
rockchip: video: Add remove() methods
Add remove() methods for EDP and VOP so that U-Boot can shut down the
video on exit. This avoids leaving DMA running while booting Linux which
can cause problems if Linux uses the frame buffer for something else.
It also makes it clear what is needed to shut down video.
While we are here, make rkvop_enable() static.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby': Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Wed, 31 May 2017 23:57:24 +0000 (17:57 -0600)]
README: Add instructions for chain-loading U-Boot
Most Chromebooks support chain-loading U-Boot but instructions are
somewhat scattered. Add a README to hold this information within the
U-Boot tree. Also add the standard developer keys to simplify the
instructions, since they are small.
Simon Glass [Wed, 31 May 2017 23:57:22 +0000 (17:57 -0600)]
tegra: clock: Avoid a divide-by-zero error
The clock fix-up for tegra is still present in the code. It causes a
divide-by-zero bug after relocation when chain-loading U-Boot from
coreboot. Fix this by adding a check.
Signed-off-by: Simon Glass <sjg@chromium.org> Fixes: 7468676 (ARM: tegra: fix clock_get_periph_rate() for UART clocks)
Simon Glass [Wed, 31 May 2017 23:57:21 +0000 (17:57 -0600)]
tegra: Enable CP15 init
At present CP15 init is disabled on tegra. Use the correct option so that
this init is performed on boot. This enables the instruction cache, for
example, which is critical to the machine running at full speed.
Simon Glass [Wed, 31 May 2017 23:57:20 +0000 (17:57 -0600)]
tegra: video: Don't power up the SOR twice
If U-Boot is the secondary boot loader, or has been run from itself, the
SOR may already be powered up. Powering it up again causes a hang, so
detect this situation and skip it.
Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Anatolij Gustschin <agust@denx.de>
Simon Glass [Wed, 31 May 2017 23:57:18 +0000 (17:57 -0600)]
tegra: spi: Wait a little after setting the clocks
For devices that need a delay between SPI transactions we seem to need an
additional delay before the first one if the CPU is running at full speed.
Add this, under control of the existing setting. At present it will only
be enabled with the Chrome OS EC.
Simon Glass [Wed, 31 May 2017 23:57:16 +0000 (17:57 -0600)]
tegra: Init clocks even when SPL did not run
At present early clock init happens in SPL. If SPL did not run (because
for example U-Boot is chain-loaded from another boot loader) then the
clocks are not set as U-Boot expects.
Add a function to detect this and call the early clock init in U-Boot
proper.
Simon Glass [Wed, 31 May 2017 23:57:14 +0000 (17:57 -0600)]
arm: Disable LPAE if not enabled
If CONFIG_ARMV7_LPAE is not defined we should make sure that the feature
is disabled. This can happen if U-Boot is chain-loaded from another boot
loader which does enable LPAE.
Simon Glass [Wed, 31 May 2017 23:57:13 +0000 (17:57 -0600)]
arm: Don't try to support CONFIG_ARMV7_LPAE on ARMv4T
At present if CONFIG_ARMV7_LPAE is defined then mmu_setup() will use
instructions which are invalid on ARMv4T. This happens on Tegra since it
has an ARMv4T boot CPU. Add a check for the architecture version to allow
the code to be built. It will not actually be executed by the boot CPU,
but needs to compile.
Sekhar Nori [Fri, 2 Jun 2017 12:37:12 +0000 (18:07 +0530)]
davinci: omapl138_lcdk: fix tXSNR DDR2 timing value
As per the datasheet[1] available for DDR2 part on board
the OMAP-L138 LCDK, the tXSNR (exit self refresh to a
non-read command) is 137.5 ns. This corresponds to a
value of 20 to be written to T_XSNR register field of
OMAP-L138's DDR configuration. The DDR2 is at 150 MHz.
Fix this. The correct value also appears on the initialization
scripts (called CCS GEL files) available on TI's wiki pages[2]
Rename command ls to fsls as its conflicting with
generic file systesm command ls and this is causing
compilation failure as below, if both are enabled
and this patch fixes it.
cmd/jffs2.o:(.u_boot_list_2_cmd_2_ls+0x0):
multiple definition of `_u_boot_list_2_cmd_2_ls'
cmd/fs.o:(.u_boot_list_2_cmd_2_ls+0x0):first defined here
scripts/Makefile.build:359: recipe for target 'cmd/built-in.o'
failed
make[1]: *** [cmd/built-in.o] Error 1
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Vikas Manocha [Sun, 28 May 2017 19:55:14 +0000 (12:55 -0700)]
spl: stm32f7: configure for xip booting
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Vikas Manocha [Sun, 28 May 2017 19:55:11 +0000 (12:55 -0700)]
SPL: Add XIP booting support
Enable support for XIP (execute in place) of U-Boot or kernel image. There is
no need to copy image from flash to ram if flash supports execute in place.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com> Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Vikas Manocha [Sun, 28 May 2017 19:55:10 +0000 (12:55 -0700)]
stm32: stm32f7: add spl build support
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit] Signed-off-by: Tom Rini <trini@konsulko.com>
Jernej Skrabec [Fri, 19 May 2017 15:41:16 +0000 (17:41 +0200)]
sunxi: video: Add support for CSC and TVE to DE2 driver
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.
Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Jernej Skrabec [Fri, 19 May 2017 15:41:14 +0000 (17:41 +0200)]
sunxi: video: Rename tve.c to tve_common.c
In order to avoid future confusion with similary named files, rename
tve.c to tve_common.c. New name better represents the fact that this file
holds code which can be and will be shared between multiple drivers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Marek Vasut [Sat, 13 May 2017 13:51:14 +0000 (15:51 +0200)]
mmc: sh_sdhi: Fix Kconfig entry
The Kconfig entry depends on RMOBILE, but this was renamed
to ARCH_RMOBILE in commit 1cc95f6e1b38 (ARM: Rmobile: Rename
CONFIG_RMOBILE to CONFIG_ARCH_RMOBILE) . Fix this omission.
Kouei Abe [Sat, 13 May 2017 13:51:18 +0000 (15:51 +0200)]
mmc: sh_sdhi: Add SDHI support
R-Car Gen3 series have four SD card interfaces (SDHI0 to SDHI3),
two of which can also be used as MMC interfaces (SDHI2 and SDHI3).
This adds High-speed mode SD clock frequency between 25MHz and 50MHz,
8bit/4bit bus width, high capacity and low voltage device support.
Simon Glass [Mon, 29 May 2017 21:31:31 +0000 (15:31 -0600)]
patman: Add a functional test
The existing test (patman --test) only covers basic checkpatch output.
We have had some problems with unicode processing and could use test
coverage for the various tags patman supports.
Add a new functional test which runs most of the patman flow on a few
test commits and checks that the results are correct.
See the documentation in the test for a description of what it does.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 29 May 2017 21:31:29 +0000 (15:31 -0600)]
patman: Add a maintainer test feature to MakeCcFile()
Allow the add_maintainers parameter to be a list of maintainers, thus
allowing us to simulate calling the script in tests without actually
needing it to work.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Simon Glass [Mon, 29 May 2017 21:31:24 +0000 (15:31 -0600)]
patman: Don't convert input data to unicode
The communication filter reads data in blocks and converts each block to
unicode (if necessary) one at a time. In the unlikely event that a unicode
character in the input spans a block this will not work. We get an error
like:
UnicodeDecodeError: 'utf8' codec can't decode bytes in position 1022-1023:
unexpected end of data
There is no need to change the input to unicode, so the easiest fix is to
drop this feature.
Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Philipp Tomsich [Mon, 29 May 2017 21:31:22 +0000 (15:31 -0600)]
patman: encode CC list to UTF-8
This change encodes the CC list to UTF-8 to avoid failures on
maintainer-addresses that include non-ASCII characters (observed on
Debian 7.11 with Python 2.7.3).
Without this, I get the following failure:
Traceback (most recent call last):
File "tools/patman/patman", line 159, in <module>
options.add_maintainers)
File "[snip]/u-boot/tools/patman/series.py", line 234, in MakeCcFile
print(commit.patch, ', '.join(set(list)), file=fd)
UnicodeEncodeError: 'ascii' codec can't encode character u'\xfc' in position 81: ordinal not in range(128)
from Heiko's email address:
[..., u'"Heiko St\xfcbner" <heiko@sntech.de>', ...]
While with this change added this encodes to:
"=?UTF-8?q?Heiko=20St=C3=BCbner?= <heiko@sntech.de>"
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Mon, 22 May 2017 17:48:52 +0000 (13:48 -0400)]
buildman: Fix bloat option when 'new' only drops functions
In the case where a new build only decreases sizes and does not increase
any size we still want to report what functions have been dropped when
doing a bloat comparison.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Tom Rini [Sun, 14 May 2017 00:11:30 +0000 (20:11 -0400)]
sandbox: Fix comparison of unsigned enum expression warning
In os_dirent_get_typename() we are checking that type falls within the
known values of the enum os_dirent_t. With clang-3.8 testing this value
as being >= 0 results in a warning as it will always be true. This
assumes of course that we are only given valid data. Given that we want
to sanity check the input, we change this to check that it falls within
the range of the first to the last entry in the given enum.
Cc: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
Vikas Manocha [Sun, 28 May 2017 19:55:08 +0000 (12:55 -0700)]
spl: armv7m: to keep ARM v7M in thumb mode before booting next image
On ARM v7M, the processor will return to ARM mode when executing blx
instruction with bit 0 of the address == 0. Always set it to 1 to stay in thumb
mode.
At present, it is applied only for raw U-Boot. This patch moves it to just
before booting next image. This way armv7m will be in thumb mode for any image
like raw or image with header like zImage or standard U-Boot.
Tom Rini [Thu, 8 Jun 2017 16:14:11 +0000 (12:14 -0400)]
Merge git://git.denx.de/u-boot-rockchip
Here is additional rk3368 and rk3399 support, rv1108 support,
refactoring HDMI video (brought in from Anatolij's tree to resolve
conflicts), some mkimage fixes and a few other things.
Philipp Tomsich [Wed, 31 May 2017 15:59:36 +0000 (17:59 +0200)]
rockchip: board: puma_rk3399: enable BMP_16BPP, BMP_24BPP and BMP_32BPP
With video output support for the RK3399-Q7 (Puma) available, we want
CMD_BMP enabled and the support for 16bit, 24bit and 32bit BMPs
defined.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 2
- enable SYS_WHITE_ON_BLACK via defconfig Reviewed-by: Simon Glass <sjg@chromium.org>
Philipp Tomsich [Wed, 31 May 2017 15:59:34 +0000 (17:59 +0200)]
rockchip: video: rk3399: add HDMI TX support on the RK3399
This commit enables the RK3399 HDMI TX, which is very similar to the
one found on the RK3288. As requested by Simon, this splits the HDMI
driver into a SOC-specific portion (rk3399_hdmi.c, rk3288_hdmi.c) and
a common portion (rk_hdmi.c).
Note that the I2C communication for reading the EDID works well with
the default settings, but does not with the alternate settings used on
the RK3288... this configuration aspect is reflected by the driverdata
for the RK3399 driver.
Having some sort of DTS-based configuration for the regulator
dependencies would be nice for the future, but for now we simply use
lists of regulator names (also via driverdata) that we probe.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: Simon Glass <sjg@chromium.org>
projects / u-boot.git / log
