From: Masahiro Yamada Date: Fri, 4 Apr 2014 06:25:05 +0000 (+0900) Subject: powerpc: remove ADS860, FADS823, FADS850SAR, FADS860T support X-Git-Url: http://git.dujemihanovic.xyz/%22/img/sics.gif/%22/static/git-favicon.png?a=commitdiff_plain;h=aa6e1e45cfc16d9ea199d18c639cca2a388823a2;p=u-boot.git powerpc: remove ADS860, FADS823, FADS850SAR, FADS860T support Enough time has passed since these boards were moved to Orphan. Remove. - Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h} - Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS), defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD) - Remove the entries from boards.cfg Signed-off-by: Masahiro Yamada --- diff --git a/arch/powerpc/cpu/mpc8xx/scc.c b/arch/powerpc/cpu/mpc8xx/scc.c index 94c9969e3f..647f05817b 100644 --- a/arch/powerpc/cpu/mpc8xx/scc.c +++ b/arch/powerpc/cpu/mpc8xx/scc.c @@ -461,18 +461,6 @@ static int scc_init (struct eth_device *dev, bd_t * bis) #error Configuration Error: exactly ONE of PB_ENET_TENA, PC_ENET_TENA must be defined #endif -#if defined(CONFIG_ADS) && defined(CONFIG_MPC860) - /* - * Port C is used to control the PHY,MC68160. - */ - immr->im_ioport.iop_pcdir |= - (PC_ENET_ETHLOOP | PC_ENET_TPFLDL | PC_ENET_TPSQEL); - - immr->im_ioport.iop_pcdat |= PC_ENET_TPFLDL; - immr->im_ioport.iop_pcdat &= ~(PC_ENET_ETHLOOP | PC_ENET_TPSQEL); - *((uint *) BCSR1) &= ~BCSR1_ETHEN; -#endif /* MPC860ADS */ - #ifdef CONFIG_RPXCLASSIC *((uchar *) BCSR0) &= ~BCSR0_ETHLPBK; *((uchar *) BCSR0) |= (BCSR0_ETHEN | BCSR0_COLTEST | BCSR0_FULLDPLX); diff --git a/arch/powerpc/cpu/mpc8xx/serial.c b/arch/powerpc/cpu/mpc8xx/serial.c index cb48ed942f..f7ca11e394 100644 --- a/arch/powerpc/cpu/mpc8xx/serial.c +++ b/arch/powerpc/cpu/mpc8xx/serial.c @@ -173,7 +173,7 @@ static int smc_init (void) # endif #endif -#if defined(CONFIG_FADS) || defined(CONFIG_ADS) +#if defined(CONFIG_FADS) /* Enable RS232 */ #if defined(CONFIG_8xx_CONS_SMC1) *((uint *) BCSR1) &= ~BCSR1_RS232EN_1; diff --git a/board/fads/fads.c b/board/fads/fads.c index 89dd9efe78..fdb46b1f35 100644 --- a/board/fads/fads.c +++ b/board/fads/fads.c @@ -210,11 +210,7 @@ static int _draminit (uint base, uint noMbytes, uint edo, uint delay) switch (noMbytes) { case 4: /* 4 Mbyte uses only CS2 */ -#ifdef CONFIG_ADS - memctl->memc_mamr = 0xc0a21114; -#else memctl->memc_mamr = 0x13a01114; /* PTA 0x13 AMA 010 */ -#endif memctl->memc_or2 = 0xffc00800; /* 4M */ break; @@ -226,11 +222,7 @@ static int _draminit (uint base, uint noMbytes, uint edo, uint delay) break; case 16: /* 16 Mbyte uses only CS2 */ -#ifdef CONFIG_ADS /* XXX: why PTA=0x60 only in 16M case? - NTL */ - memctl->memc_mamr = 0x60b21114; /* PTA 0x60 AMA 011 */ -#else memctl->memc_mamr = 0x13b01114; /* PTA 0x13 AMA 011 */ -#endif memctl->memc_or2 = 0xff000800; /* 16M */ break; @@ -674,42 +666,6 @@ int testdram (void) * Check Board Identity: */ -#if defined(CONFIG_FADS) && defined(CONFIG_SYS_DAUGHTERBOARD) -static void checkdboard(void) -{ - /* get db type from BCSR 3 */ - uint k = (*((uint *)BCSR3) >> 24) & 0x3f; - - puts (" with db "); - - switch(k) { - case 0x03 : - puts ("MPC823"); - break; - case 0x20 : - puts ("MPC801"); - break; - case 0x21 : - puts ("MPC850"); - break; - case 0x22 : - puts ("MPC821, MPC860 / MPC860SAR / MPC860T"); - break; - case 0x23 : - puts ("MPC860SAR"); - break; - case 0x24 : - case 0x2A : - puts ("MPC860T"); - break; - case 0x3F : - puts ("MPC850SAR"); - break; - default : printf("0x%x", k); - } -} -#endif /* defined(CONFIG_FADS) && defined(CONFIG_SYS_DAUGHTERBOARD) */ - int checkboard (void) { #if defined(CONFIG_MPC86xADS) @@ -732,27 +688,12 @@ int checkboard (void) puts (" rev "); switch (r) { -#if defined(CONFIG_ADS) - case 0x00: - puts ("ENG - this board sucks, check the errata, not supported\n"); - return -1; - case 0x01: - puts ("PILOT - warning, read errata \n"); - break; - case 0x02: - puts ("A - warning, read errata \n"); - break; - case 0x03: - puts ("B\n"); - break; -#else /* FADS */ case 0x00: puts ("ENG\n"); break; case 0x01: puts ("PILOT\n"); break; -#endif /* CONFIG_ADS */ default: printf ("unknown (0x%x)\n", r); return -1; @@ -865,12 +806,6 @@ int pcmcia_init(void) #endif case 5: printf("; using 5V"); -#ifdef CONFIG_ADS - /* - ** Enable 5 volt Vcc. - */ - *((uint *)BCSR1) &= ~BCSR1_PCCVCCON; -#endif #ifdef CONFIG_FADS /* ** Enable 5 volt Vcc. diff --git a/board/fads/fads.h b/board/fads/fads.h index fa49080fb7..1be00b9048 100644 --- a/board/fads/fads.h +++ b/board/fads/fads.h @@ -66,13 +66,8 @@ * motherboard and FEC Ethernet on daughterboard. All new PQ1 chips have * got FEC so FEC is the default. */ -#ifndef CONFIG_ADS #undef CONFIG_SCC1_ENET /* Disable SCC1 ethernet */ #define CONFIG_FEC_ENET /* Use FEC ethernet */ -#else /* Old ADS has not got FEC option */ -#define CONFIG_SCC1_ENET /* Use SCC1 ethernet */ -#undef CONFIG_FEC_ENET /* No FEC ethernet */ -#endif /* !CONFIG_ADS */ #if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) #error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured diff --git a/board/fads/lamp.c b/board/fads/lamp.c index 4e58291c06..ffcc2b3c41 100644 --- a/board/fads/lamp.c +++ b/board/fads/lamp.c @@ -1,7 +1,5 @@ #include -#ifndef CONFIG_ADS /* Old ADS has not got any user-controllable LED */ - #include void @@ -43,5 +41,3 @@ fast_blink(unsigned int n) signal_delay(0x00100000); } } - -#endif /* !CONFIG_ADS */ diff --git a/board/fads/pcmcia.c b/board/fads/pcmcia.c index 99fe0b4fb9..996f032f64 100644 --- a/board/fads/pcmcia.c +++ b/board/fads/pcmcia.c @@ -14,11 +14,7 @@ #ifdef CONFIG_PCMCIA -#ifdef CONFIG_ADS -#define PCMCIA_BOARD_MSG "ADS" -#else #define PCMCIA_BOARD_MSG "FADS" -#endif int pcmcia_voltage_set(int slot, int vcc, int vpp) { @@ -33,9 +29,6 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp) switch(vcc) { case 0: reg = 0; break; -#ifdef CONFIG_ADS - case 50: reg = BCSR1_PCCVCCON; break; -#endif #ifdef CONFIG_FADS case 33: reg = BCSR1_PCCVCC0 | BCSR1_PCCVCC1; break; case 50: reg = BCSR1_PCCVCC1; break; @@ -45,9 +38,6 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp) /* first, turn off all power */ -#ifdef CONFIG_ADS - *((uint *)BCSR1) |= BCSR1_PCCVCCON; -#endif #ifdef CONFIG_FADS *((uint *)BCSR1) &= ~(BCSR1_PCCVCC0 | BCSR1_PCCVCC1); #endif @@ -55,9 +45,6 @@ int pcmcia_voltage_set(int slot, int vcc, int vpp) /* enable new powersettings */ -#ifdef CONFIG_ADS - *((uint *)BCSR1) &= ~reg; -#endif #ifdef CONFIG_FADS *((uint *)BCSR1) |= reg; #endif diff --git a/boards.cfg b/boards.cfg index e411a7b90c..2125e9042f 100644 --- a/boards.cfg +++ b/boards.cfg @@ -1248,7 +1248,3 @@ Orphan powerpc mpc8260 - - - Orphan powerpc mpc8260 - - rpxsuper RPXsuper - - Orphan powerpc mpc8xx - - - RPXClassic - - Orphan powerpc mpc8xx - - - RPXlite - - -Orphan powerpc mpc8xx - - fads ADS860 - - -Orphan powerpc mpc8xx - - fads FADS823 - - -Orphan powerpc mpc8xx - - fads FADS850SAR - - -Orphan powerpc mpc8xx - - fads FADS860T - - diff --git a/include/commproc.h b/include/commproc.h index e3bc6d65d3..605aac2ec2 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -429,38 +429,6 @@ typedef struct scc_enet { * #define FEC_ENET to enable the SCC resp. FEC ethernet drivers. **********************************************************************/ - -/*** ADS *************************************************************/ - -#if defined(CONFIG_MPC860) && defined(CONFIG_ADS) -/* This ENET stuff is for the MPC860ADS with ethernet on SCC1. - */ - -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 - -#define PA_ENET_RXD ((ushort)0x0001) -#define PA_ENET_TXD ((ushort)0x0002) -#define PA_ENET_TCLK ((ushort)0x0100) -#define PA_ENET_RCLK ((ushort)0x0200) - -#define PB_ENET_TENA ((uint)0x00001000) - -#define PC_ENET_CLSN ((ushort)0x0010) -#define PC_ENET_RENA ((ushort)0x0020) - -#define SICR_ENET_MASK ((uint)0x000000ff) -#define SICR_ENET_CLKRT ((uint)0x0000002c) - -/* 68160 PHY control */ - -#define PC_ENET_ETHLOOP ((ushort)0x0800) -#define PC_ENET_TPFLDL ((ushort)0x0400) -#define PC_ENET_TPSQEL ((ushort)0x0200) - -#endif /* MPC860ADS */ - /*** BSEIP **********************************************************/ #ifdef CONFIG_BSEIP @@ -563,62 +531,6 @@ typedef struct scc_enet { #endif -/*** FADS823 ********************************************************/ - -#if defined(CONFIG_MPC823FADS) && defined(CONFIG_FADS) -/* This ENET stuff is for the MPC823FADS with ethernet on SCC2. - */ -#ifdef CONFIG_SCC2_ENET -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define CPMVEC_ENET CPMVEC_SCC2 -#endif - -#ifdef CONFIG_SCC1_ENET -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 -#define CPMVEC_ENET CPMVEC_SCC1 -#endif - -#define PA_ENET_RXD ((ushort)0x0004) -#define PA_ENET_TXD ((ushort)0x0008) -#define PA_ENET_TCLK ((ushort)0x0400) -#define PA_ENET_RCLK ((ushort)0x0200) - -#define PB_ENET_TENA ((uint)0x00002000) - -#define PC_ENET_CLSN ((ushort)0x0040) -#define PC_ENET_RENA ((ushort)0x0080) - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002e00) - -#endif /* CONFIG_FADS823FADS */ - -/*** FADS850SAR ********************************************************/ - -#if defined(CONFIG_MPC850SAR) && defined(CONFIG_FADS) -/* This ENET stuff is for the MPC850SAR with ethernet on SCC2. Some of - * this may be unique to the FADS850SAR configuration. - * Note TENA is on Port B. - */ -#define PROFF_ENET PROFF_SCC2 -#define CPM_CR_ENET CPM_CR_CH_SCC2 -#define SCC_ENET 1 -#define PA_ENET_RXD ((ushort)0x0004) /* PA 13 */ -#define PA_ENET_TXD ((ushort)0x0008) /* PA 12 */ -#define PA_ENET_RCLK ((ushort)0x0200) /* PA 6 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA 4 */ -#define PB_ENET_TENA ((uint)0x00002000) /* PB 18 */ -#define PC_ENET_CLSN ((ushort)0x0040) /* PC 9 */ -#define PC_ENET_RENA ((ushort)0x0080) /* PC 8 */ - -#define SICR_ENET_MASK ((uint)0x0000ff00) -#define SICR_ENET_CLKRT ((uint)0x00002f00) /* RCLK-CLK2, TCLK-CLK4 */ -#endif /* CONFIG_FADS850SAR */ - /*** FADS860T********************************************************/ #if defined(CONFIG_FADS) && defined(CONFIG_MPC86x) diff --git a/include/configs/ADS860.h b/include/configs/ADS860.h deleted file mode 100644 index 82ea172d7a..0000000000 --- a/include/configs/ADS860.h +++ /dev/null @@ -1,60 +0,0 @@ -/* - * A collection of structures, addresses, and values associated with - * the Motorola 860 ADS board. Copied from the MBX stuff. - * Magnus Damm added defines for 8xxrom and extended bd_info. - * Helmut Buchsbaum added bitvalues for BCSRx - * - * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) - * - * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com - * - * Values common to all FADS family boards are in board/fads/fads.h - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* Board type */ -#define CONFIG_ADS 1 /* Old Motorola MPC821/860ADS */ - -/* Processor type */ -#define CONFIG_MPC860 1 - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE - -#define CONFIG_BAUDRATE 38400 /* Console baudrate */ - -#if 0 -#define CONFIG_SYS_8XX_FACT 1526 /* 32.768 kHz crystal on XTAL/EXTAL */ -#else -#define CONFIG_SYS_8XX_FACT 12 /* 4 MHz oscillator on EXTCLK */ -#endif - -#define CONFIG_SYS_PLPRCR (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -#define CONFIG_DRAM_50MHZ 1 - - -/* - * Command line configuration. - */ -#include - -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_IMMAP -#define CONFIG_CMD_PCMCIA -#define CONFIG_CMD_PING - -/* This is picked up again in fads.h */ -#define FADS_COMMANDS_ALREADY_DEFINED - -#include "../../board/fads/fads.h" - -#define CONFIG_SYS_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */ - -#endif /* __CONFIG_H */ diff --git a/include/configs/FADS823.h b/include/configs/FADS823.h deleted file mode 100644 index 50de4ea084..0000000000 --- a/include/configs/FADS823.h +++ /dev/null @@ -1,472 +0,0 @@ - /* - * A collection of structures, addresses, and values associated with - * the Motorola 860T FADS board. Copied from the MBX stuff. - * Magnus Damm added defines for 8xxrom and extended bd_info. - * Helmut Buchsbaum added bitvalues for BCSRx - * - * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) - */ - -/* - * 1999-nov-26: The FADS is using the following physical memorymap: - * - * ff020000 -> ff02ffff : pcmcia io remapping - * ff010000 -> ff01ffff : BCSR connected to CS1, setup by U-Boot - * ff000000 -> ff00ffff : IMAP internal in the cpu - * e0000000 -> f3ffffff : pcmcia memory remapping by m8xx_pcmcia - * fe000000 -> fe1fffff : flash connected to CS0, setup by U-Boot - * 00000000 -> nnnnnnnn : sdram/dram setup by U-Boot -*/ - -#define CONFIG_SYS_PCMCIA_IO_ADDR 0xff020000 -#define CONFIG_SYS_PCMCIA_IO_SIZE 0x10000 -#define CONFIG_SYS_PCMCIA_MEM_ADDR 0xe0000000 -#define CONFIG_SYS_PCMCIA_MEM_SIZE 0x10000 -#define CONFIG_SYS_IMMR 0xFF000000 -#define CONFIG_SYS_SDRAM_SIZE (4<<20) /* standard FADS has 4M */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_FLASH_BASE 0x02800000 -#define BCSR_ADDR ((uint) 0xff010000) -#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CONFIG_ETHADDR 08:00:22:50:70:63 /* Ethernet address */ -#define CONFIG_ENV_OVERWRITE 1 /* Overwrite the environment */ - -#define CONFIG_VIDEO 1 /* To enable video controller support */ -#define CONFIG_HARD_I2C 1 /* To I2C with hardware support */ -#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CONFIG_SYS_I2C_SLAVE 0x7F - -/*#define CONFIG_PCMCIA 1 / * To enable PCMCIA support */ - -/* Video related */ - -#define CONFIG_VIDEO_LOGO 1 /* Show the logo */ -#define CONFIG_VIDEO_ENCODER_AD7176 1 /* Enable this encoder */ -#define CONFIG_VIDEO_ENCODER_AD7176_ADDR 0x54 /* Default on fads */ -#define CONFIG_VIDEO_SIZE (2*1024*1024) -/* #define CONFIG_VIDEO_ADDR (gd->bd->bi_memsize - CONFIG_VIDEO_SIZE) Frame buffer address */ - -/* Wireless 56Khz 4PPM keyboard on SMCx */ - -/*#define CONFIG_KEYBOARD 1 */ -#define CONFIG_WL_4PPM_KEYBOARD_SMC 0 /* SMC to use (0 indexed) */ - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC823 1 -#define CONFIG_MPC823FADS 1 -#define CONFIG_FADS 1 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 115200 - -/* Set the CPU speed to 50Mhz on the FADS */ - -#if 0 -#define MPC8XX_FACT 10 /* Multiply by 10 */ -#define MPC8XX_XIN 5000000 /* 5 MHz in */ -#else -#define MPC8XX_FACT 10 /* Multiply by 10 */ -#define MPC8XX_XIN 5000000 /* 5 MHz in */ -#define CONFIG_SYS_PLPRCR_MF (MPC8XX_FACT-1) << 20 /* From 0 to 4095 */ -#endif -#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#if 1 -#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */ -#define CONFIG_LOADS_ECHO 0 /* Dont echoes received characters */ -#define CONFIG_BOOTARGS "" -#define CONFIG_BOOTCOMMAND \ -"bootp ;" \ -"setenv bootargs console=tty0 console=ttyS0 " \ -"root=/dev/nfs nfsroot=${serverip}:${rootpath} " \ -"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}:eth0:off ;" \ -"bootm" -#else -#define CONFIG_BOOTDELAY 0 /* autoboot disabled */ -#endif - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_NISDOMAIN -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_DNS -#define CONFIG_BOOTP_DNS2 -#define CONFIG_BOOTP_SEND_HOSTNAME -#define CONFIG_BOOTP_NTPSERVER -#define CONFIG_BOOTP_TIMEOFFSET - - -/* - * Command line configuration. - */ -#include - - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x01000000 /* 0 ... 16 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Also NOTE that it doesn't mean SDRAM - it means MEMORY. - */ -#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ -#if 0 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer * - * interrupt status bit - leave PLL multiplication factor unchanged ! - */ -#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST | CONFIG_SYS_PLPRCR_MF) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - - /*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* Because of the way the 860 starts up and assigns CS0 the -* entire address space, we have to set the memory controller -* differently. Normally, you write the option register -* first, and then enable the chip select by writing the -* base register. For CS0, you must write the base register -* first, followed by the option register. -*/ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ -/* the other CS:s are determined by looking at parameters in BCSRx */ - -#define BCSR_SIZE ((uint)(64 * 1024)) - -#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */ - -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */ - -/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - -/* BCSRx - Board Control and Status Registers */ -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */ -#define CONFIG_SYS_BR1_PRELIM ((BCSR_ADDR) | BR_V ) - - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ - -/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -#define CONFIG_SYS_MAMR 0x13a01114 - -/* values according to the manual */ - -#define BCSR0 ((uint) (BCSR_ADDR + 00)) -#define BCSR1 ((uint) (BCSR_ADDR + 0x04)) -#define BCSR2 ((uint) (BCSR_ADDR + 0x08)) -#define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) -#define BCSR4 ((uint) (BCSR_ADDR + 0x10)) - -/* FADS bitvalues by Helmut Buchsbaum - * see MPC8xxADS User's Manual for a proper description - * of the following structures - */ - -#define BCSR0_ERB ((uint)0x80000000) -#define BCSR0_IP ((uint)0x40000000) -#define BCSR0_BDIS ((uint)0x10000000) -#define BCSR0_BPS_MASK ((uint)0x0C000000) -#define BCSR0_ISB_MASK ((uint)0x01800000) -#define BCSR0_DBGC_MASK ((uint)0x00600000) -#define BCSR0_DBPC_MASK ((uint)0x00180000) -#define BCSR0_EBDF_MASK ((uint)0x00060000) - -#define BCSR1_FLASH_EN ((uint)0x80000000) -#define BCSR1_DRAM_EN ((uint)0x40000000) -#define BCSR1_ETHEN ((uint)0x20000000) -#define BCSR1_IRDEN ((uint)0x10000000) -#define BCSR1_FLASH_CFG_EN ((uint)0x08000000) -#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) -#define BCSR1_BCSR_EN ((uint)0x02000000) -#define BCSR1_RS232EN_1 ((uint)0x01000000) -#define BCSR1_PCCEN ((uint)0x00800000) -#define BCSR1_PCCVCC0 ((uint)0x00400000) -#define BCSR1_PCCVPP_MASK ((uint)0x00300000) -#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) -#define BCSR1_RS232EN_2 ((uint)0x00040000) -#define BCSR1_SDRAM_EN ((uint)0x00020000) -#define BCSR1_PCCVCC1 ((uint)0x00010000) - -#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) -#define BCSR2_FLASH_PD_SHIFT 28 -#define BCSR2_DRAM_PD_MASK ((uint)0x07800000) -#define BCSR2_DRAM_PD_SHIFT 23 -#define BCSR2_EXTTOLI_MASK ((uint)0x00780000) -#define BCSR2_DBREVNR_MASK ((uint)0x00030000) - -#define BCSR3_DBID_MASK ((ushort)0x3800) -#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) -#define BCSR3_BREVNR0 ((ushort)0x0080) -#define BCSR3_FLASH_PD_MASK ((ushort)0x0070) -#define BCSR3_BREVN1 ((ushort)0x0008) -#define BCSR3_BREVN2_MASK ((ushort)0x0003) - -#define BCSR4_ETHLOOP ((uint)0x80000000) -#define BCSR4_TFPLDL ((uint)0x40000000) -#define BCSR4_TPSQEL ((uint)0x20000000) -#define BCSR4_SIGNAL_LAMP ((uint)0x10000000) -#ifdef CONFIG_MPC823 -#define BCSR4_USB_EN ((uint)0x08000000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860SAR -#define BCSR4_UTOPIA_EN ((uint)0x08000000) -#endif /* CONFIG_MPC860SAR */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETH_EN ((uint)0x08000000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_USB_SPEED ((uint)0x04000000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHCFG0 ((uint)0x04000000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_VCCO ((uint)0x02000000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHFDE ((uint)0x02000000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_VIDEO_ON ((uint)0x00800000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC823 -#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHCFG1 ((uint)0x00400000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_VIDEO_RST ((uint)0x00200000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHRST ((uint)0x00200000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_MODEM_EN ((uint)0x00100000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC823 -#define BCSR4_DATA_VOICE ((uint)0x00080000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC850 -#define BCSR4_DATA_VOICE ((uint)0x00080000) -#endif /* CONFIG_MPC850 */ - -#define CONFIG_DRAM_50MHZ 1 -#define CONFIG_SDRAM_50MHZ - -/* We don't use the 8259. -*/ -#define NR_8259_INTS 0 - -/* - * MPC8xx CPM Options - */ -#define CONFIG_SCC_ENET 1 -#define CONFIG_SCC2_ENET 1 -#undef CONFIG_FEC_ENET -#undef CONFIG_CPM_IIC -#undef CONFIG_UCODE_PATCH - -#define CONFIG_DISK_SPINUP_TIME 1000000 - -/* PCMCIA configuration */ - -#define PCMCIA_MAX_SLOTS 1 - -#ifdef CONFIG_MPC860 -#define PCMCIA_SLOT_A 1 -#endif - -#define CONFIG_SYS_DAUGHTERBOARD - -#endif /* __CONFIG_H */ diff --git a/include/configs/FADS850SAR.h b/include/configs/FADS850SAR.h deleted file mode 100644 index d48460b9f5..0000000000 --- a/include/configs/FADS850SAR.h +++ /dev/null @@ -1,415 +0,0 @@ - /* - * A collection of structures, addresses, and values associated with - * the Motorola 860T FADS board. Copied from the MBX stuff. - * Magnus Damm added defines for 8xxrom and extended bd_info. - * Helmut Buchsbaum added bitvalues for BCSRx - * - * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) - */ - -/* - * 1999-nov-26: The FADS is using the following physical memorymap: - * - * ff020000 -> ff02ffff : pcmcia - * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom - * ff000000 -> ff00ffff : IMAP internal in the cpu - * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom - * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_MPC850 1 -#define CONFIG_MPC850SAR 1 -#define CONFIG_FADS 1 - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 9600 - -#if 0 -#define MPC8XX_FACT 10 /* Multiply by 10 */ -#define MPC8XX_XIN 50000000 /* 50 MHz in */ -#else -#define MPC8XX_FACT 12 /* Multiply by 12 */ -#define MPC8XX_XIN 4000000 /* 4 MHz in */ -#endif -#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) - -#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ - -#if 1 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BOOTCOMMAND "bootm 02880000" /* autoboot command */ -#define CONFIG_BOOTARGS " " - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include - - -/* - * Miscellaneous configurable options - */ -#undef CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 -#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - * Also NOTE that it doesn't mean SDRAM - it means MEMORY. - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 -#define CONFIG_SYS_SDRAM_SIZE (4<<20) /* standard FADS has 4M */ -#define CONFIG_SYS_FLASH_BASE 0x02800000 -#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ -#if 0 -#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */ -#else -#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ -#endif -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE -#define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ -#define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ -#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) - -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * Reset PLL lock status sticky bit, timer expired status bit and timer * - * interrupt status bit - leave PLL multiplication factor unchanged ! - */ -#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << 20) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_TBS | \ - SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ - SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ - SCCR_DFALCD00) - - /*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* Because of the way the 860 starts up and assigns CS0 the -* entire address space, we have to set the memory controller -* differently. Normally, you write the option register -* first, and then enable the chip select by writing the -* base register. For CS0, you must write the base register -* first, followed by the option register. -*/ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ -/* the other CS:s are determined by looking at parameters in BCSRx */ - - -#define BCSR_ADDR ((uint) 0x02100000) -#define BCSR_SIZE ((uint)(64 * 1024)) - -#define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ -#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */ - -#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */ - -/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) - -/* BCSRx - Board Control and Status Registers */ -#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP -#define CONFIG_SYS_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */ -#define CONFIG_SYS_BR1_PRELIM ((BCSR_ADDR) | BR_V ) - - -/* - * Memory Periodic Timer Prescaler - */ - -/* periodic timer for refresh */ -#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ - -/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ -#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ - -/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ -#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ -#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ - -/* - * MAMR settings for SDRAM - */ - -/* 8 column SDRAM */ -#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) -/* 9 column SDRAM */ -#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ - MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ - MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) - -#define CONFIG_SYS_MAMR 0x13a01114 - -/* values according to the manual */ - - -#define PCMCIA_MEM_ADDR ((uint)0xff020000) -#define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) - -#define BCSR0 ((uint) (BCSR_ADDR + 00)) -#define BCSR1 ((uint) (BCSR_ADDR + 0x04)) -#define BCSR2 ((uint) (BCSR_ADDR + 0x08)) -#define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) -#define BCSR4 ((uint) (BCSR_ADDR + 0x10)) - -/* FADS bitvalues by Helmut Buchsbaum - * see MPC8xxADS User's Manual for a proper description - * of the following structures - */ - -#define BCSR0_ERB ((uint)0x80000000) -#define BCSR0_IP ((uint)0x40000000) -#define BCSR0_BDIS ((uint)0x10000000) -#define BCSR0_BPS_MASK ((uint)0x0C000000) -#define BCSR0_ISB_MASK ((uint)0x01800000) -#define BCSR0_DBGC_MASK ((uint)0x00600000) -#define BCSR0_DBPC_MASK ((uint)0x00180000) -#define BCSR0_EBDF_MASK ((uint)0x00060000) - -#define BCSR1_FLASH_EN ((uint)0x80000000) -#define BCSR1_DRAM_EN ((uint)0x40000000) -#define BCSR1_ETHEN ((uint)0x20000000) -#define BCSR1_IRDEN ((uint)0x10000000) -#define BCSR1_FLASH_CFG_EN ((uint)0x08000000) -#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) -#define BCSR1_BCSR_EN ((uint)0x02000000) -#define BCSR1_RS232EN_1 ((uint)0x01000000) -#define BCSR1_PCCEN ((uint)0x00800000) -#define BCSR1_PCCVCC0 ((uint)0x00400000) -#define BCSR1_PCCVPP_MASK ((uint)0x00300000) -#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) -#define BCSR1_RS232EN_2 ((uint)0x00040000) -#define BCSR1_SDRAM_EN ((uint)0x00020000) -#define BCSR1_PCCVCC1 ((uint)0x00010000) - -#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) -#define BCSR2_FLASH_PD_SHIFT 28 -#define BCSR2_DRAM_PD_MASK ((uint)0x07800000) -#define BCSR2_DRAM_PD_SHIFT 23 -#define BCSR2_EXTTOLI_MASK ((uint)0x00780000) -#define BCSR2_DBREVNR_MASK ((uint)0x00030000) - -#define BCSR3_DBID_MASK ((ushort)0x3800) -#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) -#define BCSR3_BREVNR0 ((ushort)0x0080) -#define BCSR3_FLASH_PD_MASK ((ushort)0x0070) -#define BCSR3_BREVN1 ((ushort)0x0008) -#define BCSR3_BREVN2_MASK ((ushort)0x0003) - -#define BCSR4_ETHLOOP ((uint)0x80000000) -#define BCSR4_TFPLDL ((uint)0x40000000) -#define BCSR4_TPSQEL ((uint)0x20000000) -#define BCSR4_SIGNAL_LAMP ((uint)0x10000000) -#ifdef CONFIG_MPC823 -#define BCSR4_USB_EN ((uint)0x08000000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860SAR -#define BCSR4_UTOPIA_EN ((uint)0x08000000) -#endif /* CONFIG_MPC860SAR */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETH_EN ((uint)0x08000000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_USB_SPEED ((uint)0x04000000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHCFG0 ((uint)0x04000000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_VCCO ((uint)0x02000000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHFDE ((uint)0x02000000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_VIDEO_ON ((uint)0x00800000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC823 -#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHCFG1 ((uint)0x00400000) -#endif /* CONFIG_MPC860T */ -#ifdef CONFIG_MPC823 -#define BCSR4_VIDEO_RST ((uint)0x00200000) -#endif /* CONFIG_MPC823 */ -#ifdef CONFIG_MPC860T -#define BCSR4_FETHRST ((uint)0x00200000) -#endif /* CONFIG_MPC860T */ -#define BCSR4_MODEM_EN ((uint)0x00100000) -#define BCSR4_DATA_VOICE ((uint)0x00080000) - -#define CONFIG_DRAM_50MHZ 1 -#define CONFIG_SDRAM_50MHZ - -/* We don't use the 8259. -*/ -#define NR_8259_INTS 0 - -#define CONFIG_DISK_SPINUP_TIME 1000000 - - -/* PCMCIA configuration */ - -#define PCMCIA_MAX_SLOTS 2 - -#ifdef CONFIG_MPC860 -#define PCMCIA_SLOT_A 1 -#endif - -#define CONFIG_SYS_DAUGHTERBOARD - -#endif /* __CONFIG_H */ diff --git a/include/configs/FADS860T.h b/include/configs/FADS860T.h deleted file mode 100644 index ed7484bd1c..0000000000 --- a/include/configs/FADS860T.h +++ /dev/null @@ -1,58 +0,0 @@ -/* - * A collection of structures, addresses, and values associated with - * the Motorola 860T FADS board. Copied from the MBX stuff. - * Magnus Damm added defines for 8xxrom and extended bd_info. - * Helmut Buchsbaum added bitvalues for BCSRx - * - * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) - * - * Modified by, Yuli Barcohen, Arabella Software Ltd., yuli@arabellasw.com - * - * Values common to all FADS family boards are in board/fads/fads.h - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* board type */ -#define CONFIG_FADS 1 /* old/new FADS + new ADS */ - -/* processor type */ -#define CONFIG_MPC860T 1 /* 860T */ - -#define CONFIG_SYS_TEXT_BASE 0xFE000000 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 38400 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ - -#if 0 /* old FADS */ -# define CONFIG_SYS_8XX_FACT 12 /* 4 MHz oscillator on EXTCLK */ -#else /* new FADS */ -# define CONFIG_SYS_8XX_FACT 10 /* 5 MHz oscillator on EXTCLK */ -#endif - -#define CONFIG_SYS_PLPRCR (((CONFIG_SYS_8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -#define CONFIG_DRAM_50MHZ 1 -#define CONFIG_SDRAM_50MHZ 1 - -#include "../../board/fads/fads.h" - -#ifdef USE_REAL_FLASH_VALUES -/* - * These values fit our FADS860T ... - * The "default" behaviour with 1Mbyte initial doesn't work for us! - */ -#undef CONFIG_SYS_OR0_PRELIM -#undef CONFIG_SYS_BR0_PRELIM -#define CONFIG_SYS_OR0_PRELIM 0x0FFC00D34 /* Real values for the board */ -#define CONFIG_SYS_BR0_PRELIM 0x02800001 /* Real values for the board */ -#endif - -#define CONFIG_SYS_DAUGHTERBOARD /* FADS has processor-specific daughterboard */ - -#endif /* __CONFIG_H */ diff --git a/include/pcmcia.h b/include/pcmcia.h index ce8c8ed5e9..1ad3e636a9 100644 --- a/include/pcmcia.h +++ b/include/pcmcia.h @@ -24,8 +24,6 @@ /* The RPX series use SLOT_B */ #if defined(CONFIG_RPXCLASSIC) || defined(CONFIG_RPXLITE) # define CONFIG_PCMCIA_SLOT_B -#elif defined(CONFIG_ADS) /* The ADS board uses SLOT_A */ -# define CONFIG_PCMCIA_SLOT_A #elif defined(CONFIG_FADS) /* The FADS series are a mess */ # if defined(CONFIG_MPC86x) || defined(CONFIG_MPC821) # define CONFIG_PCMCIA_SLOT_A