From: Tom Rini Date: Fri, 6 Apr 2018 20:27:55 +0000 (-0400) Subject: mx31ads: Delete X-Git-Url: http://git.dujemihanovic.xyz/%22/img/sics.gif/%22/static/git-favicon.png?a=commitdiff_plain;h=448fc44fb87cb678594541c6695f49debb5c1be3;p=u-boot.git mx31ads: Delete This platform has been marked as orphaned since September 2013, remove. Signed-off-by: Tom Rini --- diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig index 056dacc16f..49bcf99520 100644 --- a/arch/arm/Kconfig +++ b/arch/arm/Kconfig @@ -444,11 +444,6 @@ config TARGET_X600 select SUPPORT_SPL select PL011_SERIAL -config TARGET_MX31ADS - bool "Support mx31ads" - select CPU_ARM1136 - select BOARD_EARLY_INIT_F - config TARGET_MX31PDK bool "Support mx31pdk" select BOARD_LATE_INIT @@ -1296,7 +1291,6 @@ source "board/freescale/ls1046ardb/Kconfig" source "board/freescale/ls1012aqds/Kconfig" source "board/freescale/ls1012ardb/Kconfig" source "board/freescale/ls1012afrdm/Kconfig" -source "board/freescale/mx31ads/Kconfig" source "board/freescale/mx31pdk/Kconfig" source "board/freescale/mx35pdk/Kconfig" source "board/freescale/s32v234evb/Kconfig" diff --git a/board/freescale/mx31ads/Kconfig b/board/freescale/mx31ads/Kconfig deleted file mode 100644 index eeeb6f490f..0000000000 --- a/board/freescale/mx31ads/Kconfig +++ /dev/null @@ -1,15 +0,0 @@ -if TARGET_MX31ADS - -config SYS_BOARD - default "mx31ads" - -config SYS_VENDOR - default "freescale" - -config SYS_SOC - default "mx31" - -config SYS_CONFIG_NAME - default "mx31ads" - -endif diff --git a/board/freescale/mx31ads/MAINTAINERS b/board/freescale/mx31ads/MAINTAINERS deleted file mode 100644 index 5f6ec268c7..0000000000 --- a/board/freescale/mx31ads/MAINTAINERS +++ /dev/null @@ -1,6 +0,0 @@ -MX31ADS BOARD -#M: (resigned) Guennadi Liakhovetski -S: Orphan (since 2013-09) -F: board/freescale/mx31ads/ -F: include/configs/mx31ads.h -F: configs/mx31ads_defconfig diff --git a/board/freescale/mx31ads/Makefile b/board/freescale/mx31ads/Makefile deleted file mode 100644 index 5e1440d596..0000000000 --- a/board/freescale/mx31ads/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Copyright (C) 2008, Guennadi Liakhovetski -# -# SPDX-License-Identifier: GPL-2.0+ -# - -obj-y := mx31ads.o -obj-y += lowlevel_init.o diff --git a/board/freescale/mx31ads/lowlevel_init.S b/board/freescale/mx31ads/lowlevel_init.S deleted file mode 100644 index fcb5549d77..0000000000 --- a/board/freescale/mx31ads/lowlevel_init.S +++ /dev/null @@ -1,268 +0,0 @@ -/* - * Copyright (C) 2008, Guennadi Liakhovetski - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include - -.macro REG reg, val - ldr r2, =\reg - ldr r3, =\val - str r3, [r2] -.endm - -.macro REG8 reg, val - ldr r2, =\reg - ldr r3, =\val - strb r3, [r2] -.endm - -.macro DELAY loops - ldr r2, =\loops -1: - subs r2, r2, #1 - nop - bcs 1b -.endm - -/* RedBoot: AIPS setup - Only setup MPROTx registers. - * The PACR default values are good.*/ -.macro init_aips - /* - * Set all MPROTx to be non-bufferable, trusted for R/W, - * not forced to user-mode. - */ - ldr r0, =0x43F00000 - ldr r1, =0x77777777 - str r1, [r0, #0x00] - str r1, [r0, #0x04] - ldr r0, =0x53F00000 - str r1, [r0, #0x00] - str r1, [r0, #0x04] - - /* - * Clear the on and off peripheral modules Supervisor Protect bit - * for SDMA to access them. Did not change the AIPS control registers - * (offset 0x20) access type - */ - ldr r0, =0x43F00000 - ldr r1, =0x0 - str r1, [r0, #0x40] - str r1, [r0, #0x44] - str r1, [r0, #0x48] - str r1, [r0, #0x4C] - ldr r1, [r0, #0x50] - and r1, r1, #0x00FFFFFF - str r1, [r0, #0x50] - - ldr r0, =0x53F00000 - ldr r1, =0x0 - str r1, [r0, #0x40] - str r1, [r0, #0x44] - str r1, [r0, #0x48] - str r1, [r0, #0x4C] - ldr r1, [r0, #0x50] - and r1, r1, #0x00FFFFFF - str r1, [r0, #0x50] -.endm /* init_aips */ - -/* RedBoot: MAX (Multi-Layer AHB Crossbar Switch) setup */ -.macro init_max - ldr r0, =0x43F04000 - /* MPR - priority is M4 > M2 > M3 > M5 > M0 > M1 */ - ldr r1, =0x00302154 - str r1, [r0, #0x000] /* for S0 */ - str r1, [r0, #0x100] /* for S1 */ - str r1, [r0, #0x200] /* for S2 */ - str r1, [r0, #0x300] /* for S3 */ - str r1, [r0, #0x400] /* for S4 */ - /* SGPCR - always park on last master */ - ldr r1, =0x10 - str r1, [r0, #0x010] /* for S0 */ - str r1, [r0, #0x110] /* for S1 */ - str r1, [r0, #0x210] /* for S2 */ - str r1, [r0, #0x310] /* for S3 */ - str r1, [r0, #0x410] /* for S4 */ - /* MGPCR - restore default values */ - ldr r1, =0x0 - str r1, [r0, #0x800] /* for M0 */ - str r1, [r0, #0x900] /* for M1 */ - str r1, [r0, #0xA00] /* for M2 */ - str r1, [r0, #0xB00] /* for M3 */ - str r1, [r0, #0xC00] /* for M4 */ - str r1, [r0, #0xD00] /* for M5 */ -.endm /* init_max */ - -/* RedBoot: M3IF setup */ -.macro init_m3if - /* Configure M3IF registers */ - ldr r1, =0xB8003000 - /* - * M3IF Control Register (M3IFCTL) - * MRRP[0] = L2CC0 not on priority list (0 << 0) = 0x00000000 - * MRRP[1] = L2CC1 not on priority list (0 << 0) = 0x00000000 - * MRRP[2] = MBX not on priority list (0 << 0) = 0x00000000 - * MRRP[3] = MAX1 not on priority list (0 << 0) = 0x00000000 - * MRRP[4] = SDMA not on priority list (0 << 0) = 0x00000000 - * MRRP[5] = MPEG4 not on priority list (0 << 0) = 0x00000000 - * MRRP[6] = IPU1 on priority list (1 << 6) = 0x00000040 - * MRRP[7] = IPU2 not on priority list (0 << 0) = 0x00000000 - * ------------ - * 0x00000040 - */ - ldr r0, =0x00000040 - str r0, [r1] /* M3IF control reg */ -.endm /* init_m3if */ - -/* RedBoot: To support 133MHz DDR */ -.macro init_drive_strength - /* - * Disable maximum drive strength SDRAM/DDR lines by clearing DSE1 bits - * in SW_PAD_CTL registers - */ - - /* SDCLK */ - ldr r1, =0x43FAC200 - ldr r0, [r1, #0x6C] - bic r0, r0, #(1 << 12) - str r0, [r1, #0x6C] - - /* CAS */ - ldr r0, [r1, #0x70] - bic r0, r0, #(1 << 22) - str r0, [r1, #0x70] - - /* RAS */ - ldr r0, [r1, #0x74] - bic r0, r0, #(1 << 2) - str r0, [r1, #0x74] - - /* CS2 (CSD0) */ - ldr r0, [r1, #0x7C] - bic r0, r0, #(1 << 22) - str r0, [r1, #0x7C] - - /* DQM3 */ - ldr r0, [r1, #0x84] - bic r0, r0, #(1 << 22) - str r0, [r1, #0x84] - - /* DQM2, DQM1, DQM0, SD31-SD0, A25-A0, MA10 (0x288..0x2DC) */ - ldr r2, =22 /* (0x2E0 - 0x288) / 4 = 22 */ -pad_loop: - ldr r0, [r1, #0x88] - bic r0, r0, #(1 << 22) - bic r0, r0, #(1 << 12) - bic r0, r0, #(1 << 2) - str r0, [r1, #0x88] - add r1, r1, #4 - subs r2, r2, #0x1 - bne pad_loop -.endm /* init_drive_strength */ - -/* CPLD on CS4 setup */ -.macro init_cs4 - ldr r0, =WEIM_BASE - ldr r1, =0x0000D843 - str r1, [r0, #0x40] - ldr r1, =0x22252521 - str r1, [r0, #0x44] - ldr r1, =0x22220A00 - str r1, [r0, #0x48] -.endm /* init_cs4 */ - -.globl lowlevel_init -lowlevel_init: - - /* Redboot initializes very early AIPS, what for? - * Then it also initializes Multi-Layer AHB Crossbar Switch, - * M3IF */ - /* Also setup the Peripheral Port Remap register inside the core */ - ldr r0, =0x40000015 /* start from AIPS 2GB region */ - mcr p15, 0, r0, c15, c2, 4 - - init_aips - - init_max - - init_m3if - - init_drive_strength - - init_cs4 - - /* Image Processing Unit: */ - /* Too early to switch display on? */ - REG IPU_CONF, IPU_CONF_DI_EN /* Switch on Display Interface */ - /* Clock Control Module: */ - REG CCM_CCMR, 0x074B0BF5 /* Use CKIH, MCU PLL off */ - - DELAY 0x40000 - - REG CCM_CCMR, 0x074B0BF5 | CCMR_MPE /* MCU PLL on */ - REG CCM_CCMR, (0x074B0BF5 | CCMR_MPE) & ~CCMR_MDS /* Switch to MCU PLL */ - - /* PBC CPLD on CS4 */ - mov r1, #CS4_BASE - ldrh r1, [r1, #0x2] - /* Is 27MHz switch set? */ - ands r1, r1, #0x10 - - /* 532-133-66.5 */ - ldr r0, =CCM_BASE - ldr r1, =0xFF871D58 - /* PDR0 */ - str r1, [r0, #0x4] - ldreq r1, MPCTL_PARAM_532 - ldrne r1, MPCTL_PARAM_532_27 - /* MPCTL */ - str r1, [r0, #0x10] - - /* Set UPLL=240MHz, USB=60MHz */ - ldr r1, =0x49FCFE7F - /* PDR1 */ - str r1, [r0, #0x8] - ldreq r1, UPCTL_PARAM_240 - ldrne r1, UPCTL_PARAM_240_27 - /* UPCTL */ - str r1, [r0, #0x14] - /* default CLKO to 1/8 of the ARM core */ - mov r1, #0x000002C0 - add r1, r1, #0x00000006 - /* COSR */ - str r1, [r0, #0x1c] - - /* RedBoot sets 0x3f, 7, 7, 3, 5, 1, 3, 0 */ -/* REG CCM_PDR0, PDR0_CSI_PODF(0x3f) | PDR0_CSI_PRDF(7) | PDR0_PER_PODF(7) | PDR0_HSP_PODF(2) | PDR0_NFC_PODF(6) | PDR0_IPG_PODF(1) | PDR0_MAX_PODF(2) | PDR0_MCU_PODF(0)*/ - - /* Redboot: 0, 51, 10, 12 / 0, 14, 9, 13 */ -/* REG CCM_MPCTL, PLL_PD(0) | PLL_MFD(0x33) | PLL_MFI(7) | PLL_MFN(0x23)*/ - /* Default: 1, 4, 12, 1 */ - REG CCM_SPCTL, PLL_PD(1) | PLL_MFD(4) | PLL_MFI(12) | PLL_MFN(1) - - /* B8xxxxxx - NAND, 8xxxxxxx - CSD0 RAM */ - REG 0xB8001010, 0x00000004 - REG 0xB8001004, 0x006ac73a - REG 0xB8001000, 0x92100000 - REG 0x80000f00, 0x12344321 - REG 0xB8001000, 0xa2100000 - REG 0x80000000, 0x12344321 - REG 0x80000000, 0x12344321 - REG 0xB8001000, 0xb2100000 - REG8 0x80000033, 0xda - REG8 0x81000000, 0xff - REG 0xB8001000, 0x82226080 - REG 0x80000000, 0xDEADBEEF - REG 0xB8001010, 0x0000000c - - mov pc, lr - -MPCTL_PARAM_532: - .word (((1-1) << 26) + ((52-1) << 16) + (10 << 10) + (12 << 0)) -MPCTL_PARAM_532_27: - .word (((1-1) << 26) + ((15-1) << 16) + (9 << 10) + (13 << 0)) -UPCTL_PARAM_240: - .word (((2-1) << 26) + ((13-1) << 16) + (9 << 10) + (3 << 0)) -UPCTL_PARAM_240_27: - .word (((2-1) << 26) + ((9 -1) << 16) + (8 << 10) + (8 << 0)) diff --git a/board/freescale/mx31ads/mx31ads.c b/board/freescale/mx31ads/mx31ads.c deleted file mode 100644 index ad89cb021d..0000000000 --- a/board/freescale/mx31ads/mx31ads.c +++ /dev/null @@ -1,114 +0,0 @@ -/* - * Copyright (C) 2008, Guennadi Liakhovetski - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include -#include -#include -#include -#include -#include - -DECLARE_GLOBAL_DATA_PTR; - -int dram_init(void) -{ - /* dram_init must store complete ramsize in gd->ram_size */ - gd->ram_size = get_ram_size((void *)PHYS_SDRAM_1, - PHYS_SDRAM_1_SIZE); - return 0; -} - -int board_early_init_f(void) -{ - int i; - - /* CS0: Nor Flash */ - /* - * CS0L and CS0A values are from the RedBoot sources by Freescale - * and are also equal to those used by Sascha Hauer for the Phytec - * i.MX31 board. CS0U is just a slightly optimized hardware default: - * the only non-zero field "Wait State Control" is set to half the - * default value. - */ - static const struct mxc_weimcs cs0 = { - /* sp wp bcd bcs psz pme sync dol cnc wsc ew wws edc */ - CSCR_U(0, 0, 0, 0, 0, 0, 0, 0, 0, 15, 0, 0, 0), - /* oea oen ebwa ebwn csa ebc dsz csn psr cre wrap csen */ - CSCR_L(1, 0, 0, 0, 0, 1, 5, 0, 0, 0, 1, 1), - /* ebra ebrn rwa rwn mum lah lbn lba dww dct wwu age cnc2 fce*/ - CSCR_A(0, 0, 7, 2, 0, 0, 2, 1, 0, 0, 0, 0, 0, 0) - }; - - mxc_setup_weimcs(0, &cs0); - - /* setup pins for UART1 */ - mx31_gpio_mux(MUX_RXD1__UART1_RXD_MUX); - mx31_gpio_mux(MUX_TXD1__UART1_TXD_MUX); - mx31_gpio_mux(MUX_RTS1__UART1_RTS_B); - mx31_gpio_mux(MUX_CTS1__UART1_CTS_B); - - /* SPI2 */ - mx31_gpio_mux(MUX_CSPI2_SS2__CSPI2_SS2_B); - mx31_gpio_mux(MUX_CSPI2_SCLK__CSPI2_CLK); - mx31_gpio_mux(MUX_CSPI2_SPI_RDY__CSPI2_DATAREADY_B); - mx31_gpio_mux(MUX_CSPI2_MOSI__CSPI2_MOSI); - mx31_gpio_mux(MUX_CSPI2_MISO__CSPI2_MISO); - mx31_gpio_mux(MUX_CSPI2_SS0__CSPI2_SS0_B); - mx31_gpio_mux(MUX_CSPI2_SS1__CSPI2_SS1_B); - - /* start SPI2 clock */ - __REG(CCM_CGR2) = __REG(CCM_CGR2) | (3 << 4); - - /* PBC setup */ - /* Enable UART transceivers also reset the Ethernet/external UART */ - readw(CS4_BASE + 4); - - writew(0x8023, CS4_BASE + 4); - - /* RedBoot also has an empty loop with 100000 iterations here - - * clock doesn't run yet */ - for (i = 0; i < 100000; i++) - ; - - /* Clear the reset, toggle the LEDs */ - writew(0xDF, CS4_BASE + 6); - - /* clock still doesn't run */ - for (i = 0; i < 100000; i++) - ; - - /* See 1.5.4 in IMX31ADSE_PERI_BUS_CNTRL_CPLD_RM.pdf */ - readb(CS4_BASE + 8); - readb(CS4_BASE + 7); - readb(CS4_BASE + 8); - readb(CS4_BASE + 7); - - return 0; -} - -int board_init(void) -{ - gd->bd->bi_boot_params = 0x80000100; /* adress of boot parameters */ - - return 0; -} - -int checkboard(void) -{ - printf("Board: MX31ADS\n"); - return 0; -} - -#ifdef CONFIG_CMD_NET -int board_eth_init(bd_t *bis) -{ - int rc = 0; -#ifdef CONFIG_CS8900 - rc = cs8900_initialize(0, CONFIG_CS8900_BASE); -#endif - return rc; -} -#endif diff --git a/board/freescale/mx31ads/u-boot.lds b/board/freescale/mx31ads/u-boot.lds deleted file mode 100644 index 71a63f188e..0000000000 --- a/board/freescale/mx31ads/u-boot.lds +++ /dev/null @@ -1,110 +0,0 @@ -/* - * January 2004 - Changed to support H4 device - * Copyright (c) 2004 Texas Instruments - * - * (C) Copyright 2002 - * Gary Jennejohn, DENX Software Engineering, - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -OUTPUT_FORMAT("elf32-littlearm", "elf32-littlearm", "elf32-littlearm") -OUTPUT_ARCH(arm) -ENTRY(_start) -SECTIONS -{ - . = 0x00000000; - - . = ALIGN(4); - .text : - { - *(.__image_copy_start) - /* WARNING - the following is hand-optimized to fit within */ - /* the sector layout of our flash chips! XXX FIXME XXX */ - - * (.vectors) - arch/arm/cpu/arm1136/start.o (.text*) - board/freescale/mx31ads/built-in.o (.text*) - arch/arm/lib/built-in.o (.text*) - net/built-in.o (.text*) - drivers/mtd/built-in.o (.text*) - - . = DEFINED(env_offset) ? env_offset : .; - env/embedded.o(.text*) - - *(.text*) - } - . = ALIGN(4); - .rodata : { *(.rodata*) } - - . = ALIGN(4); - .data : { - *(.data*) - } - - . = ALIGN(4); - - . = ALIGN(4); - .u_boot_list : { - KEEP(*(SORT(.u_boot_list*))); - } - - . = ALIGN(4); - - .image_copy_end : - { - *(.__image_copy_end) - } - - .rel_dyn_start : - { - *(.__rel_dyn_start) - } - - .rel.dyn : { - *(.rel*) - } - - .rel_dyn_end : - { - *(.__rel_dyn_end) - } - - .hash : { *(.hash*) } - - .end : - { - *(.__end) - } - - _image_binary_end = .; - -/* - * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c - * __bss_base and __bss_limit are for linker only (overlay ordering) - */ - - .bss_start __rel_dyn_start (OVERLAY) : { - KEEP(*(.__bss_start)); - __bss_base = .; - } - - .bss __bss_base (OVERLAY) : { - *(.bss*) - . = ALIGN(4); - __bss_limit = .; - } - .bss_end __bss_limit (OVERLAY) : { - KEEP(*(.__bss_end)); - } - - .dynsym _image_binary_end : { *(.dynsym) } - .dynbss : { *(.dynbss) } - .dynstr : { *(.dynstr*) } - .dynamic : { *(.dynamic*) } - .gnu.hash : { *(.gnu.hash) } - .plt : { *(.plt*) } - .interp : { *(.interp*) } - .gnu : { *(.gnu*) } - .ARM.exidx : { *(.ARM.exidx*) } -} diff --git a/configs/mx31ads_defconfig b/configs/mx31ads_defconfig deleted file mode 100644 index 9a4622577c..0000000000 --- a/configs/mx31ads_defconfig +++ /dev/null @@ -1,15 +0,0 @@ -CONFIG_ARM=y -CONFIG_TARGET_MX31ADS=y -CONFIG_SYS_TEXT_BASE=0xA0000000 -# CONFIG_AUTO_COMPLETE is not set -CONFIG_CMD_IMLS=y -CONFIG_CMD_SPI=y -# CONFIG_CMD_SETEXPR is not set -CONFIG_CMD_DHCP=y -CONFIG_CMD_PING=y -CONFIG_CMD_DATE=y -CONFIG_ENV_IS_IN_FLASH=y -CONFIG_MXC_GPIO=y -# CONFIG_MMC is not set -CONFIG_MTD_NOR_FLASH=y -CONFIG_MXC_SPI=y diff --git a/include/configs/mx31ads.h b/include/configs/mx31ads.h deleted file mode 100644 index 0fe37c71da..0000000000 --- a/include/configs/mx31ads.h +++ /dev/null @@ -1,145 +0,0 @@ -/* - * Copyright (C) 2008, Guennadi Liakhovetski - * - * Configuration settings for the MX31ADS Freescale board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -#include - - /* High Level Configuration Options */ -#define CONFIG_MX31 1 /* This is a mx31 */ - -#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024) - -/* - * Hardware drivers - */ - -#define CONFIG_MXC_UART -#define CONFIG_MXC_UART_BASE UART1_BASE - -#define CONFIG_HARD_SPI 1 -#define CONFIG_DEFAULT_SPI_BUS 1 -#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH) - -/* PMIC Controller */ -#define CONFIG_POWER -#define CONFIG_POWER_SPI -#define CONFIG_POWER_FSL -#define CONFIG_FSL_PMIC_BUS 1 -#define CONFIG_FSL_PMIC_CS 0 -#define CONFIG_FSL_PMIC_CLK 1000000 -#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH) -#define CONFIG_FSL_PMIC_BITLEN 32 -#define CONFIG_RTC_MC13XXX - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_CONS_INDEX 1 - -#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */ - -#define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "uboot_addr=0xa0000000\0" \ - "uboot=mx31ads/u-boot.bin\0" \ - "kernel=mx31ads/uImage\0" \ - "nfsroot=/opt/eldk/arm\0" \ - "bootargs_base=setenv bootargs console=ttymxc0,115200\0" \ - "bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \ - "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ - "bootcmd=run bootcmd_net\0" \ - "bootcmd_net=run bootargs_base bootargs_nfs; " \ - "tftpboot ${loadaddr} ${kernel}; bootm\0" \ - "prg_uboot=tftpboot ${loadaddr} ${uboot}; " \ - "protect off ${uboot_addr} 0xa003ffff; " \ - "erase ${uboot_addr} 0xa003ffff; " \ - "cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \ - "setenv filesize; saveenv\0" - -#define CONFIG_CS8900 -#define CONFIG_CS8900_BASE 0xb4020300 -#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */ - -/* - * The MX31ADS board seems to have a hardware "peculiarity" confirmed under - * U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A - * controller inverted. The controller is capable of detecting and correcting - * this, but it needs 4 network packets for that. Which means, at startup, you - * will not receive answers to the first 4 packest, unless there have been some - * broadcasts on the network, or your board is on a hub. Reducing the ARP - * timeout from default 5 seconds to 200ms we speed up the initial TFTP - * transfer, should the user wish one, significantly. - */ -#define CONFIG_ARP_TIMEOUT 200UL - -/* - * Miscellaneous configurable options - */ - -#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x10000 - -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 -#define PHYS_SDRAM_1 CSD0_BASE -#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024) - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR -#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ - GENERATED_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_GBL_DATA_OFFSET) - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_SYS_FLASH_BASE CS0_BASE -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 262 /* max number of sectors on one chip */ -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */ -#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */ - -#define CONFIG_ENV_SECT_SIZE (128 * 1024) -#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) - -/* Address and size of Redundant Environment Sector */ -#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) -#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE - -/*----------------------------------------------------------------------- - * CFI FLASH driver setup - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */ -#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */ -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */ - -/* - * JFFS2 partitions - */ -#define CONFIG_JFFS2_DEV "nor0" - -#endif /* __CONFIG_H */