serial: serial_msm: added pinmux & config

Serial port configuration was missing from previous implementation.
It only worked because it was preconfigured by LK.
This patch configures the uart for 115200 8N1.
It also configures the pin mux for uart pins using DT bindings.

Signed-off-by: Ramon Fried <ramon.fried@gmail.com>

diff --git a/drivers/serial/serial_msm.c b/drivers/serial/serial_msm.c
index a4279accb4f7ffa8d75a35d179ad7f7d777fa72a..c462394dbdcd22b82b6b240ee84e50aef1b1a83e 100644 (file)
--- a/drivers/serial/serial_msm.c
+++ b/drivers/serial/serial_msm.c
@@ -16,6 +16,7 @@
 #include <watchdog.h>
 #include <asm/io.h>
 #include <linux/compiler.h>
+#include <dm/pinctrl.h>
 
 /* Serial registers - this driver works in uartdm mode*/
 
@@ -25,6 +26,9 @@
 #define UARTDM_RXFS             0x50 /* RX channel status register */
 #define UARTDM_RXFS_BUF_SHIFT   0x7  /* Number of bytes in the packing buffer */
 #define UARTDM_RXFS_BUF_MASK    0x7
+#define UARTDM_MR1                              0x00
+#define UARTDM_MR2                              0x04
+#define UARTDM_CSR                              0xA0
 
 #define UARTDM_SR                0xA4 /* Status register */
 #define UARTDM_SR_RX_READY       (1 << 0) /* Word is the receiver FIFO */
@@ -45,6 +49,10 @@
 #define UARTDM_TF               0x100 /* UART Transmit FIFO register */
 #define UARTDM_RF               0x140 /* UART Receive FIFO register */
 
+#define UART_DM_CLK_RX_TX_BIT_RATE 0xCC
+#define MSM_BOOT_UART_DM_8_N_1_MODE 0x34
+#define MSM_BOOT_UART_DM_CMD_RESET_RX 0x10
+#define MSM_BOOT_UART_DM_CMD_RESET_TX 0x20
 
 DECLARE_GLOBAL_DATA_PTR;
 
@@ -179,6 +187,14 @@ static int msm_uart_clk_init(struct udevice *dev)
        return 0;
 }
 
+static void uart_dm_init(struct msm_serial_data *priv)
+{
+       writel(UART_DM_CLK_RX_TX_BIT_RATE, priv->base + UARTDM_CSR);
+       writel(0x0, priv->base + UARTDM_MR1);
+       writel(MSM_BOOT_UART_DM_8_N_1_MODE, priv->base + UARTDM_MR2);
+       writel(MSM_BOOT_UART_DM_CMD_RESET_RX, priv->base + UARTDM_CR);
+       writel(MSM_BOOT_UART_DM_CMD_RESET_TX, priv->base + UARTDM_CR);
+}
 static int msm_serial_probe(struct udevice *dev)
 {
        int ret;
@@ -192,12 +208,8 @@ static int msm_serial_probe(struct udevice *dev)
        if (ret)
                return ret;
 
-       if (readl(priv->base + UARTDM_SR) & UARTDM_SR_UART_OVERRUN)
-               writel(UARTDM_CR_CMD_RESET_ERR, priv->base + UARTDM_CR);
-
-       writel(0, priv->base + UARTDM_IMR);
-       writel(UARTDM_CR_CMD_STALE_EVENT_DISABLE, priv->base + UARTDM_CR);
-       msm_serial_fetch(dev);
+       pinctrl_select_state(dev, "uart");
+       uart_dm_init(priv);
 
        return 0;
 }