Commit
f11513d99787 ("net: phy: realtek: Add tx/rx delay config for
8211e") made the Realtek PHY driver honour the phy-mode DT property,
to set up the proper delay scheme for the RX and TX lines. A similar
change in the kernel revealed that those properties were mostly wrong.
The kernel DTs got updated over the last few months, but we were missing
out on the U-Boot version.
Just sync in the phy-mode properties from the mainline kernel,
v5.17-rc7, to avoid the breaking DT sync that late in the cycle.
This fixes Ethernet operation on the affected boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
&emac {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>;
- phy-mode = "rgmii-id";
+ phy-mode = "rgmii-txid";
phy-handle = <&ext_rgmii_phy>;
phy-supply = <®_dc1sw>;
status = "okay";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
};
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
};
pinctrl-names = "default";
pinctrl-0 = <&gmac_pins_rgmii_a>, <&gmac_phy_reset_pin_hummingbird>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
snps,reset-gpio = <&pio 0 21 GPIO_ACTIVE_HIGH>;
snps,reset-active-low;
snps,reset-delays-us = <0 10000 30000>;
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-supply = <®_gmac_3v3>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-supply = <®_gmac_3v3>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
phy-supply = <®_gmac_3v3>;
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
phy1: ethernet-phy@1 {
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
phy1: ethernet-phy@1 {
pinctrl-names = "default";
pinctrl-0 = <&gmac_rgmii_pins>;
phy = <&phy1>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
phy1: ethernet-phy@1 {
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_sw>;
phy-handle = <&rgmii_phy>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
allwinner,rx-delay-ps = <700>;
allwinner,tx-delay-ps = <700>;
status = "okay";
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_dldo4>;
phy-handle = <&rgmii_phy>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
};
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
};
pinctrl-0 = <&emac_rgmii_pins>;
phy-supply = <®_gmac_3v3>;
phy-handle = <&ext_rgmii_phy>;
- phy-mode = "rgmii";
+ phy-mode = "rgmii-id";
status = "okay";
};